Manual Skil 7208 (page 9 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78247

Zoom out

Zoom in

1/108

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• SKIL can assure awless functioning of the tool only

when original accessories are used

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A); wear

ear protection

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• When sanding metal, sparks are generated; do not use

dustbag/dustbox and keep other persons and

combustible material from work area

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of sanding sheet 4

! disconnect the plug

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total sanding surface

covered with sanding paper

- mount VELCRO sanding sheet as illustrated

• Mounting support plate 5

- remove VELCRO sanding sheet

- remove delta tip A while pushing button B

- mount support plate C as illustrated

• Mounting special sanding attachments 6

- mount desired sanding attachment to support plate C

as illustrated

- mount corresponding VELCRO sanding sheet to

sanding attachment

- 3 sanding positions

• Mounting “Louvre” attachment 7

- remove VELCRO sanding sheet

- remove delta tip A while pushing button B

- mount “Louvre” attachment as illustrated

• Dust suction 8

- mount dustbox/dustbag E

- empty dustbox/dustbag E regularly for optimal dust

pick-up performance

! do not use dustbox/dustbag when sanding metal

• On/o switch

- switch on/o the tool by pushing switch F 2 forward/

backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

• Spot light 9 (7208)

Spot light G automatically lights on when activating

switch F

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7208 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 7208 Manual

Product: