701602
10
Zoom out
Zoom in
Previous page
1/112
Next page
10
- for sanding of rough or plain wood use medium grit
sizes (80, 100, 120)
- for smoothing of wood and surfaces with old paint as
well as for nishing of bare wood use ne grit sizes
(180, 240, 320)
Use dierent grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- nish with ne grit
For more tips see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool and cord clean (especially ventilation
slots D
2
)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
ENVIRONMENT
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol
5
will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
Measured in accordance with EN 62841 the sound
pressure level of this tool is 82.5 dB(A) and the sound
power level 93.5 dB(A) (standard deviation: 3 dB), and
the vibration 10.1 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! 
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
On/o switch
- switch on/o the tool by pushing switch B
2
forward/
backwards
! before the sanding surface reaches the workpiece,
you should switch on the tool
! 
the workpiece
Speed control
8
For optimal sanding results on dierent materials
- with wheel C
2
you can set the desired sanding speed
- before starting a job, nd the optimal speed and grit by
testing out on spare material
Holding and guiding the tool
! 
coloured grip area(s)
9
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let the
sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots D
2
uncovered
Turnable foot
q
! unplug tool before removing/mounting backing
pads
! pad screw H becomes hot during use; do not
touch it before it has cooled down
- for changing front tip of sanding sheet/sanding foot
when it is worn or damaged
- for changing foot position depending on working
surface (see: Application advice)
- take hex key E from storage F
- remove VELCRO sanding sheet G
- remove pad screw H with hex key E
- turn backing pad J 60° or 120°
- fasten pad screw H with hex key E
! 
pad screw H
Mounting special sanding attachment K (not standard
included)
w
- remove VELCRO sanding sheet G
2
- remove pad screw H with hex key E
- mount attachment K onto the tool and fasten it with pad
screw H
- mount corresponding VELCRO sanding sheet to
sanding attachment
APPLICATION ADVICE
Use the tool with the delta-tip pointing forward for corners
and edges
e
Use the tool with the at side pointing forward for long
strokes on at surfaces
r
Use the tool with special sanding attachment K
2
for
narrow and other hard-to-reach places
t
When the foampad of the delta-tip is worn or damaged at
the top, you may extend its service life twice by turning it
120° (also applicable to delta sanding sheet)
q
Never use the same sanding sheet for wood and metal
Recommended sanding sheet grits:
- for removing paint and for sanding of extremely rough
wood use coarse grit sizes (40, 60)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 7126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7126 in the language / languages: All languages as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info