701598
10
Zoom out
Zoom in
Previous page
1/100
Next page
10
- press trigger A and push tool forward to start screwing
or unscrewing
- adjust screwing depth, if necessary
Adjusting screwing depth 0
- rotate sleeve E clockwise for increasing the screwing
depth
- rotate sleeve E counter-clockwise for reducing the
screwing depth
- always test out rst on a piece of scrap material
Holding and guiding the tool
! while working, always hold the tool at the
grey-coloured grip area(s) !
- do not apply too much pressure on the tool; let the tool
do the work for you
- keep ventilation slots H 2 uncovered
Changing bit holder @
Hand strap #
Belt clip $
APPLICATION ADVICE
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
When screwdriving in hard wood one should pre-drill a hole
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
MAINTENANCE / SERVICE
Always keep tool and cord clean (especially ventilation
slots H 2)
! disconnect the plug before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
A damaged power cord shall be replaced at a SKIL
service centre only in order to avoid a hazard
ENVIRONMENT
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
Measured in accordance with EN 62841 the sound
pressure level of this tool is 84 dB(A) and the sound power
level 95 dB(A) (standard deviation: 3 dB), and the vibration
< 2.5 m/s² (triax vector sum; uncertainty K = 1.5 m/s²)
The vibration emission level has been measured in
accordance with a standardised test given in EN 62841; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Visseuse 6940
INTRODUCTION
Cet outil à rotation gauche/droite est conçu pour le
vissage et le dévissage des vis
Lisez et conservez ce manuel d’instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L’OUTIL 2
A Interrupteur marche/arrêt
B Bouton de blocage de l’interrupteur
C Levier pour inverser le sens de rotation
D Porte-embout magnétique
E Manchon pour régler la profondeur de vissage
F Agrafe de ceinture
G Dragonne
H Fentes de ventilation
SECURITE
AVERTISSEMENTS DE SECURITE GENERAUX POUR
L’OUTIL ELECTRIQUE
AVERTISSEMENT Lisez tous les avertissements de
sécurité, les instructions, les illustrations et les
spécifications fournis avec cet outil électrique. Ne pas
suivre les instructions énumérées ci-dessous peut
provoquer un choc électrique, un incendie et/ou une
blessure sérieuse. Conservez tous les avertissements et
toutes les instructions pour pouvoir s’y reporter
ultérieurement. Le terme “outil électrique” dans les
avertissements se rapporte à des outils électriques
raccordés au secteur (avec câble de raccordement) et à
des outils électriques à batterie (sans câble de
raccordement).
1) SECURITE DE LA ZONE DE TRAVAIL
a) Maintenez l’endroit de travail propre et bien éclairé.
Un lieu de travail en désordre ou mal éclairé augmente le
risque d’accidents.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 6940 MA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 6940 MA in the language / languages: All languages as an attachment in your email.

The manual is 4,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info