Manual Skil 6925 (page 7 of 96) (All languages)

644674

Zoom out

Zoom in

1/96

operation.Ifdamaged,havethepowertoolrepaired

beforeuse. Many accidents are caused by poorly

maintained power tools.

f) Keepcuttingtoolssharpandclean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Usethepowertool,accessoriesandtoolbitsetc.,in

accordancewiththeseinstructions,takinginto

accounttheworkingconditionsandtheworktobe

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5)SERVICE

a) Haveyourpowertoolservicedbyaqualifiedrepair

personusingonlyidenticalreplacementparts. This

will ensure that the safety of the power tool is maintained.

SAFETYINSTRUCTIONSFORSCREWDRIVERS

GENERAL

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool should not be used by people under the age of

16 years

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Donotworkmaterialscontainingasbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wearadustmaskandworkwithadust

extractiondevicewhenconnectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wearadustmaskand

workwithadustextractiondevicewhen

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Alwaysdisconnectplugfrompowersourcebefore

makinganyadjustmentorchanginganyaccessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

BEFOREUSE

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Securetheworkpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

DURINGUSE

• Holdpowertoolbyinsulatedgrippingsurfaces,

whenperforminganoperationwherethefastener

maycontacthiddenwiring (fasteners contacting a

“live” wire may make exposed metal parts of the power

tool “live” and could give the operator an electric shock)

• Usesuitabledetectorstofindhiddenutilitylinesor

callthelocalutilitycompanyforassistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Whenworking,alwaysholdthetoolfirmlyandtake

asecurestance (high reaction torque can briey occur

while driving in and loosening screws)

• Always keep the cord away from moving parts of the tool

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTERUSE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/o 4

• Switch locking for continuous use 5

• Speed control for smooth starting 6

• Changing direction of rotation 7

- when not properly set in left/right position, switch A 2

cannot be activated

! changedirectionofrotationonlywhentoolisata

completestandstill

• Operating the tool

! onlyusebitswithhexagonshaft

! donotusedamagedbits

- push bit to end position in bitholder

- guide screw to screwdriving bit (screw is held in place

by magnetic bit holder)

- rmly push tip of screw into workpiece

- press trigger A and push tool forward to start screwing

or unscrewing

- adjust screwing depth, if necessary

• Adjusting screwing depth 8

- rotate sleeve E clockwise for increasing the screwing

depth

- rotate sleeve E counter-clockwise for reducing the

screwing depth

- always test out rst on a piece of scrap material

• Holding and guiding the tool

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)9

- do not apply too much pressure on the tool; let the tool

do the work for you

- keep ventilation slots H 2 uncovered

• Changing bit holder 0

• Hand strap !

• Belt clip @

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 6925 in the language / languages: All languages as an attachment in your email.

The manual is 7,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 6925 Manual

Product: