758383
9
Zoom out
Zoom in
Previous page
1/104
Next page
9
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
DURING USE
Wear ear protectors when impact drilling (exposure
to noise can cause hearing loss)
Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
accessory may contact hidden wiring or its own
power cord (contact with a “live” wire will also make
exposed metal parts of the power tool “live” and shock
the operator)
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
If the drill bit becomes unexpectedly jammed (causing
a sudden, dangerous reaction), immediately switch o
the tool
AFTER USE
When you put away the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
On/o 6
Speed control for smooth starting 7
Changing direction of rotation 8
-when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Changing bits 9
-insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
Torque control (VariTorque) q
-output torque will increase as clutch ring D is rotated
from 1 to 19
-when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
-position E will lock up the clutch to permit (non-impact)
drilling or driving heavy-duty work
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage

power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) 
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR IMPACT DRILLS
GENERAL
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
This tool should not be used by people under the age of
16 years
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Never use the tool when the cord is damaged; it must be
replaced by a specially prepared cord available through
an after-sales service centre for SKIL power tools and
carried out by a qualied person
Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
SKIL can assure awless functioning of the tool only
when original accessories are used
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
BEFORE USE
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)

or call the local utility company for assistance
(contact with electric lines can lead to re or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 6225 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 6225 in the language / languages: All languages as an attachment in your email.

The manual is 4,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info