758582
14
Zoom out
Zoom in
Previous page
1/172
Next page
14
! be aware of the sudden impact when the tool is
switched on
! the tool should run at full speed before the blade
enters into the workpiece
! do not force the tool (apply light and continuous
pressure in order to avoid overheating the blade

plastic material)
! 
coloured grip area(s) y
-after completing the cut switch o tool by releasing
trigger B
! ensure that the blade has come to a complete

workpiece
Plunge cutting u
-switch on the tool
! the tool should run at full speed before the blade
enters into the workpiece
-press knob M with your thumb
-tilt tool forward with line-of-cut indicator R lined up with
desired line of cut marked on the workpiece
-gradually move tool forward
! never pull tool backwards
Parallel guide S i
-for making exact cuts along a workpiece edge
-can be inserted in either side of foot
Adjusting parallel guide
-loosen knob T
-adjust to desired cutting width by using parallel guide
scale (use line-of-cut indicator R as 0-reference)
-tighten knob T
APPLICATION ADVICE
Only use sharp saw blades of the correct type o
-use hardened steel saw blade V 2 for cutting wood,
aluminium, plastic and all sorts of laminated wood
-use diamond disc W 2 for cutting ceramics and tiles
-carbide tipped blades X 2 stay sharp up to 30 times
longer than ordinary blades
Cutting large panels p
-support panel close to the cut either on oor, table or
workbench
! set cutting depth so that you cut through panel
and not through support
-in case parallel guide does not allow desired width of
cut, clamp or nail straight piece of wood to workpiece
as a guide, and use the left side of the foot against this
guide
Splinter-free cutting
-always face the good side of the workpiece down
-fasten a straight piece of wood on the workpiece by
means of 2 clamps
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool and cord clean (especially ventilation
slots Y 2)
! disconnect the plug before cleaning
Always keep the area around lower guard Z 2 clean
(remove dust and chips by blowing out with compressed
air or with a brush)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
On/o 8
-switch on tool by rst pressing knob A forward and then
pulling trigger switch B
-switch o tool by releasing trigger switch B
Adjusting cutting depth (0-28,5 mm) 9
-loosen knob C
-set desired cutting depth using scale D
-tighten knob C
-for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
! 
cutting depth corresponds with value on cutting
depth scale D (for actual depth of cut use table q
as reference)
! 
cut
Dust suction w
-connect vacuum cleaner hose E to connection F and
vacuum cleaner as illustrated
! never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation
! do not use vacuum cleaner when cutting metal
Changing saw blade e
! disconnect the plug
! ensure that the blade has come to a complete
standstill
-set cutting depth to the maximum
-take hex key G from storage H
-push spindle-lock button J and hold it while you remove
blade boltK by turning hex key G CLOCKWISE (= in
same direction as arrow printed on saw blade)
! push spindle-lock button J only when tool is at a
standstill
-release spindle-lock button J
-remove ange L
-press knob M with your thumb
-lift up foot N and remove saw blade
! change saw blade with saw teeth and arrow
printed on saw blade pointing in same direction as
arrow on upper guard P e b
-mount ange L
-rmly tighten blade bolt K by turning hex key G
COUNTER-CLOCKWISE while pushing spindle-lock
button J
-release spindle-lock button J
Operating the tool r
-set desired cutting depth
-connect plug to power source (light Q turns on
indicating that the tool is receiving power) t
-press knob M with your thumb
-place tool with front end of foot at on workpiece
-tilt tool forward with line-of-cut indicator R lined up with
desired line of cut marked on the workpiece
! ensure that the saw teeth are not engaged into the
workpiece
-switch on the tool
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 5360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 5360 in the language / languages: All languages as an attachment in your email.

The manual is 8,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info