Manual Skil 5064 AA (page 10 of 156) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

482541

Zoom out

Zoom in

1/156

• This tool is not suitable for wet cutting

• Always disconnect plug from power source before

making any adjustment or changing any accessory

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Do not work materials containing asbestos

(asbestos is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask

and work with a dust extraction device

when connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Only use a saw table provided with a switch that prevents

restarting of the motor after interruption of voltage

• Only use a saw table provided with a kerf guide

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Use only saw blades with a minimum diameter of

184 mm, a maximum diameter of 190 mm and a

spindle hole of 16 mm

• Never use saw blades made of high speed steel (HSS)

• Never use grinding/cutting discs with this tool

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Remove all obstacles on top of as well as underneath the

cutting path before you start cutting

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• The noise level when working can exceed 85 dB(A);

wear ear protection

• Never use the tool without the original protection

guard system

• Do not attempt to cut extremely small workpieces

• Do not work overhead with the tool

• In case of jamming or electrical or mechanical

malfunction, immediately switch o the tool and

disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a

complete standstill

• After switching o your circular saw, never stop the

rotation of the saw blade by a lateral force applied

against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting saw blade 3

! disconnect the plug

- take blade wrench A from storage B

- push spindle-lock button C and hold it while you

remove blade bolt D with blade wrench

! push spindle-lock button C only when tool is at

a standstill

- release spindle-lock button C

- remove ange E

- open lower guard F with lever G and hold it while you

mount saw blade with saw teeth and arrow printed on

saw blade pointing in same direction as arrow on

lower guard

- release lower guard F

- mount ange E

! make sure that clamping surfaces H of flanges

are perfectly clean and face the blade

- push spindle-lock button C and hold it while you

tighten blade bolt with blade wrench 1/8 turn past

nger tight (ensures slippage of saw blade when it

encounters excessive resistance thus reducing motor

overload and saw kickback)

- release spindle-lock button C

• Adjusting cutting depth (0-64 mm) 4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen lever J

- raise/lower foot K until desired cutting depth is set on

scale using indicator L

- tighten lever J

• Adjusting cutting angle (0-45°) 5

- loosen knob M

- tilt tool until desired cutting angle is set on scale using

indicator N

- tighten knob M

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

• 90° Cutting angle check 5

- adjust and tighten foot K to maximum cutting depth 4

- adjust and tighten cutting angle to 0°

- check for a 90° angle between the blade and bottom of

foot with a square

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 5064 AA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 5064 AA Manual

Product: