644822
7
Zoom out
Zoom in
Previous page
1/96
Next page
7
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools. Inspect tool cords and plugs
periodically and, if damaged, have them repaired by a
qualied person.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY INSTRUCTIONS FOR BENCH
GRINDERS
This tool should not be used by people under the age of
16 years
SKIL can assure awless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
Do not use damaged, deformed or vibrating
grinding wheels
Use only grinding wheels with an allowable speed
matching at least the highest no-load speed of the
tool
Before use, check that the grinding wheels are free of
damage, properly mounted, and able to rotate freely
Replace the grinding wheel, if it is worn down to Ø
150 mm
Always mount spark guard A 2 and tool rest C 2; never
use the tool without them
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
Connect this earthed power tool only to a properly
earthed power supply system; ensure that socket
and extension cable have a functional protective
conductor
Only use the anges which are supplied with this tool
When grinding metal, sparks are generated; keep other
persons and combustible material from work area
Keep hands away from the rotating grinding wheels
Wear protective gloves 4 and use safety glasses 5
The noise level when working can exceed 85 dB(A);
wear ear protection 6
Anyone entering the work area must wear personal
protective equipment (fragments of the workpiece or of
a broken accessory may y away and cause injury
beyond the immediate area of operation)
Never grind sidewards against the rotating grinding
wheel; only grind at the front
Do not brake the grinding wheels with side pressure
Allow the tool to cool down after a continuous use of
30 minutes (S
2
30 min.) 1
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
Never use the tool when cord is damaged; have it
replaced by a qualied person
Inspect the extension cord periodically and replace it,
if damaged
Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Mounting of spark guard 7
- loosen screw B1 (do not remove it)
! regularly check the distance between spark
guard A and the grinding wheel (max. 2 mm) and
re-adjust, if necessary
- replace the grinding wheel, if it is worn down to the
point where spark guard A can no longer be adjusted
to the maximum distance of 2 mm
Mounting of tool rest 8
! regularly check the distance between tool rest C
and the grinding wheel (max. 2 mm) and
re-adjust, if necessary
Mounting tool on working surface 9
! for safe handling always mount tool on a flat and
stable working surface (e.g. workbench)
- use 4 mounting holes D for attaching the tool with
suitable screws to the working surface
- you may also clamp the tool to the working surface
with commercially available screw clamps
! remove 4 rubber supports E before mounting tool
on working surface
On/o
Switch on/o the tool by pushing switch F 2 in “I”/”O” position
Before using the tool for the rst time
- perform a sound-test on the grinding wheels (in
perfect condition they sound clear, when
tapped lightly)
- test-run the tool for at least 5 minutes without load
(stay out of danger area)
Operating the tool 0
- lower spark guard A as far as possible
- switch on tool
- lay the workpiece to be ground on tool rest C
- move the workpiece lightly from the left to the right and
back (for optimal grinding results as well as uniform
wear of the grinding wheel)
- cool the workpiece in water from time to time
- switch o tool
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3900 in the language / languages: All languages as an attachment in your email.

The manual is 6,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info