758598
12
Zoom out
Zoom in
Previous page
1/140
Next page
12
operating temperature range of -20 to +50°C --> 2

pressing button M 8c; wait until battery has returned
within the allowable operating temperature range
-the battery is nearly empty (to protect against
deep discharge)
battery level 8b is shown by the battery level indicator
when pressing button M; charge battery
! 

damaged
Changing accessories q
! remove battery from tool
-remove/mount the required accessory as illustrated
-ensure that the openings of the accessory engage into

-mount the accessory with the depressed centre
pointing downwards
-check the tight seating of the accessory (incorrect
or not securely fastened accessories can come loose

Dust suction w
! remove battery from tool
-use vacuum cleaner adapter J only when working with
sanding pad E
-mount vacuum cleaner adapter J as illustrated
-connect vacuum cleaner
! do not use dust extraction device/vacuum cleaner
when sanding metal
-clean vacuum cleaner adapter J regularly for optimal
dust pick-up performance
Mounting of sanding sheet e
-tap the dust out of the VELCRO material on sanding
pad E before mounting the sanding sheet
-mount VELCRO sanding sheet H as illustrated
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total VELCRO surface
covered with sanding paper

-2 in “I”/”O”
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! 
the workpiece
Adjusting working speed r
-with wheel D the required oscillating frequency can


-the optimal working speed depends on the material
and can be determined with practical trials
Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s) t
-keep ventilation slots K uncovered
-do not apply too much pressure on the tool (excessive
pressure will cause excessive heat and may shorten

not
standard includedy
Do not use a saw blade which is cracked, deformed or
dull
WHEN SANDING
Use the tool only for dry sanding (penetration of water

Do not touch the moving sanding sheet
Do not continue to use worn, torn or heavily clogged
sanding sheets
When sanding metal, sparks are generated; do not use
vacuum cleaner and keep other persons and combustible
material from work area
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the

Only use the following batteries and chargers with
this tool
-
-
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain

-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 This tool accepts most commonly available multi-tool
accessories, including existing OIS and Starlock basic
accessories
4 Read the instruction manual before use
5
burn battery for any reason
6 Store tool/charger/battery in locations where temperature
will not exceed 50°C
7 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Battery level indicator 8
-press the battery level indicator button M to show the
current battery level 8a
! when the lowest level of the battery indicator
8b, the
battery is empty
! 
after pressing button M 8c, the battery is not
within the allowable operating temperature range
LED-light L 9
LED-light automatically lights on when activating the on/

! 
protection is activated (see below)
Battery protection

being switched on, when
-the load is too high --> remove load and restart
-the battery temperature is not within the allowable
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3650 in the language / languages: All languages as an attachment in your email.

The manual is 6,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info