797813
11
Zoom out
Zoom in
Previous page
1/188
Next page
11
being switched on, when
-the load is too high --> remove load and restart
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start ashing when
pressing button AB 7c; wait until battery has returned
within the allowable operating temperature range
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level ub is shown by the battery level indicator
when pressing button AB; charge battery
! donotcontinuetopresstheon/oswitchafterthe
toolisswitchedoautomatically;batterymaybe
damaged
Mounting saw blade 2
! remove battery from tool
-take hex key A from storage B
-push spindle-lock button F and hold it while you remove
blade bolt AA by turning hex key A CLOCKWISE (= in
same direction as arrow printed on saw blade)
! push spindle-lock button F only when tool is at a
standstill
-release spindle-lock button F
-remove ange Z
! makesurethatclampingsurfacesXofangesare
perfectly clean and face the blade
-open lower guard W with lever S and hold it while you
mount saw blade with saw teeth and arrow printed on
saw blade pointing in same direction as arrow on upper
guard
-release lower guard W
-mount ange Z
-push spindle-lock button F and hold it while you
tighten blade bolt with hex key 1/8 turn past nger tight
(ensures slippage of saw blade when it encounters
excessive resistance thus reducing motor overload and
saw kickback)
-release spindle-lock button F
Adjusting cutting depth (0-41 mm)9
-for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
-loosen knob Q
-raise/lower foot M until desired cutting depth is set on
scale using indicator P
-tighten knob Q
Adjusting cutting angle (0-45°)q
-loosen knob U
-tilt tool until desired cutting angle is set on scale using
indicator V
-tighten knob U
! when bevel cutting, cutting depth does not
correspond with value on cutting depth scale
Line-of-cut indicator L w
-for guiding tool along desired line of cut marked on the
workpiece
-for a straight 0° cut or a 45° bevel cut use the indicator
line concerned
! the wide part of the foot should rest on the
supported part of the workpiece
! cutting width is determined by width of blade teeth
and not by width of blade body
! alwaysmaketrialcutsrsttoverifyactuallineof
cut
DURING USE
The noise level when working can exceed 85 dB(A); wear
ear protection
Never use the tool without the original protection guard
system
Do not attempt to cut extremely small workpieces
Do not work overhead with the tool
In case of jamming or electrical or mechanical
malfunction, immediately switch o the tool and remove
the battery
AFTER USE
When you put away the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
After switching o your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
BATTERIES
The battery supplied is partially charged (to ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
rst time)
Only use the following batteries and chargers with this
tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Battery level indicator 7
-press the battery level indicator button AB to show the
current battery level 7a
! when the lowest level of the battery indicator
startsashingafterpressingbuttonAB7b, the
battery is empty
! when2levelsofthebatteryindicatorstartashing
after pressing button AB 7c, the battery is not
within the allowable operating temperature range
LED-light T 8
LED-light automatically lights on when the tool starts
running
! whenLED-lightstartsashing,thebattery
protection is activated (see below)
Battery protection
The tool is suddenly being switched o or prevented from
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3540 in the language / languages: All languages as an attachment in your email.

The manual is 6.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info