758357
6
Zoom out
Zoom in
Previous page
1/52
Next page
General Specifications
Voltage Rating . . . . . . . . . . . . . . . . . . .120 V, 60 Hz
Amperage Rating . . . . . . . . . . . . . . . . . . . . . . .1.2 A
No Load Speed . . . . . . . . .No500-1,700/min (SPM)
Throat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16"
Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . .5” pin-end
Blade Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . .7/8"
Cutting Capacity . . . . . . . . . . . . . . . . . . . . .2" at 90°
Table Tilt . . . . . . . . . . . . . . . . . . . . . . . to 45° Left
Motor Specifications
In the event of a malfunction or breakdown, grounding pro-
vides a path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with an elec-
tric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a match-
ing outlet that is properly installed and grounded in accor-
dance with all local codes and ordinances.
This Scroll Saw is designed to use a 1700 RPM motor. It is
wired for operation on 110-120 volts, 60 Hz. alternating cur-
rent. Before connecting the motor cord to power source,
make certain the switch is in the “OFF” position and be sure
the electric current is of the same characteristics as
stamped on the scroll saw nameplate.
Connection ToAPower Source
This machine must be grounded while in use to protect the
operator from electric shock.
Plug power cord into a 110-120V properly grounded type
outlet protected by a 15-amp dual element time delay fuse
or circuit breaker.
Not all outlets are properly grounded. If you are not sure
that your outlet, as pictured in Fig. 1, is properly
grounded; have it checked by a qualified electrician.
To avoid electric shock, do not touch
the metal prongs on the plug when
installing or removing the plug to or from the outlet.
Failure to properly ground this power
tool can cause electrocution or seri-
ous shock, particularly when used near metal
plumbing or other metal objects. If shocked, your
reaction could cause your hands to hit the tool.
If power cord is worn, cut or damaged
in any way, have it replaced immedi-
ately to avoid shock or fire hazard.
Your unit is for use on 120 volts; it has a plug that looks
like the one in Figure 1.
This power tool is equipped with a 3-conductor cord and
grounding type plug, approved by Underwriters
Laboratories and the Canadian Standards Association.
The ground conductor has a green jacket and is
attached to the tool housing at one end and to the
ground prong in the attachment plug at the other end.
If the outlet you are planning to use for this power tool is
of the two-prong type, DO NOT REMOVE OR ALTER
THE GROUNDING PRONG IN ANY MANNER.. Have a
qualified electrician replace the TWO-prong outlet with a
properly grounded THREE-prong outlet.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The con-
ductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
conductor. If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely under-
stood, or if in doubt as to whether the tool is properly
grounded.
Always use proper extension cord. The use of any exten-
sion cord will cause some loss of power. To keep this to
aminimum and to prevent overheating and motor burn-
out, use the table below to determine the minimum wire
size (A.W.G.) extension cord. Use only 3-wire extension
cords which have 3-prong grounding type plugs and 3-
pole receptacles which accept the tool’s plug. Make sure
your extension cord is in good condition.
Extension Cord Length Wire Size A.W.G.
0-25 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
26-50 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
51-100 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
6.
Motor Specifications and Electrical Requirements
“SAVE THESE INSTRUCTIONS”
DANGER
!
DANGER
!
WARNING
!
FIG. 1
SM 2610957121 05-08 6/5/08 7:35 AM Page 6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3335-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3335-01 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info