797790
10
Zoom out
Zoom in
Previous page
1/140
Next page
10
-output torque will increase as clutch ring B is rotated
from 1 to 17
-when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
-position D will lock up the clutch to permit (non-impact)
drilling or driving heavy-duty work
-position C will lock up the clutch to permit impact
drilling only
! ensure that gear selector G is in position 2 when
function selector F is in impact drilling position
! do not use impact drilling position C for drilling in
wood, metal, ceramic and plastic to prevent the
drill/screw bit from being damaged
Mechanical gear selection e
-set selector G to desired speed
! actuate the gear selector while tool is running
slowly
1
-low speed
-high torque
-for screwdriving and drilling large diameters
-for tapping thread
2
-high speed
-lower torque
-for impact drilling
-for drilling small diameters
WORKLIGHT L r
-WORKLIGHT L will illuminate in default low brightness
mode when the tool is turned on OR if WORKLIGHT
button K is depressed without turning the tool on.
Brightness can be switched from low to full or from full
to low by pressing the WORKLIGHT button K.
-Low brightness – turns o approx. 10s after on/o
switch is released
-High brightness - turns o approx. 600s after on/o
switch is released
! WORKLIGHT button K is disabled while the tool is
running. The brightness should only be switched
when the tool is not running.
! 
protection is activated (see below)
Battery protection
The tool is suddenly being switched o or prevented from
being switched on, when
-the load is too high --> remove load and restart
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start ashing when
pressing button M7c; wait until battery has returned
within the allowable operating temperature range
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level 7b is shown by the battery level indicator
when pressing button M; charge battery
! 

damaged
Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
-keep ventilation slots H 2 uncovered
-do not apply too much pressure on the tool; let the tool
do the work for you

or call the local utility company for assistance
(contact with electric lines can lead to re or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
rst time)
Only use the following batteries and chargers with
this tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use battery when damaged; it should be replaced
immediately
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
when charging 4...40°C
during operation –20...+50°C
during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
Combined switch for on/o and speed control A 2
-control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Battery level indicator 7
-press the battery level indicator button M to show the
current battery level 7a
! when the lowest level of the battery indicator
7b, the
! battery is empty
! 
after pressing button M 7c, the battery is not
! within the allowable operating temperature range
Attaching belt clip 8
-attach the belt clip N to the drill with the supplied screw.
Integrated bit clip P 2
-conveniently store hex bits.
Strap xing Q 2
-attach a wrist strap (not included) around your hand
when carrying the tool.
Changing direction of rotation 9
-when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Changing bits q
! do not use bits with a damaged shank
Torque control (VariTorque) w
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3075 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3075 in the language / languages: All languages as an attachment in your email.

The manual is 5.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info