758370
10
Zoom out
Zoom in
Previous page
1/136
Next page
10
drilling or driving heavy-duty work
-position D will lock up the clutch to permit impact
drilling only
! ensure that gear selector B is in position 2 when
function selector C is in impact drilling position
! do not use impact drilling position D for drilling in
wood, metal, ceramic and plastic to prevent the
drill/screw bit from being damaged
Mechanical gear selection e
-set selector G to desired speed
! actuate the gear selector while tool is running
slowly
1
-low speed
-high torque
-for screwdriving and drilling large diameters
-for tapping thread
2
-high speed
-lower torque
-for impact drilling
-for drilling small diameters
Battery protection
Switches o the tool or prevents the tool from being
switched on, when
-the load is too high
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
-the lithium-ion battery is nearly empty (to protect
against deep discharge)
! 

damaged
LED-light M r
-LED-light M automatically lights on when activating
switch A r
Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
-keep ventilation slots J 2 uncovered
-do not apply too much pressure on the tool; let the tool
do the work for you
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool clean (especially ventilation slots H 2)
! remove battery from tool before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
APPLICATION ADVICE
Use the appropriate bits y
! only use sharp bits
clamping devices or in a vice is held more securely than
by hand)

or call the local utility company for assistance
(contact with electric lines can lead to re or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
DURING USE
In case of electrical or mechanical malfunction,
immediately switch o the tool or unplug charger from
power source
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
rst time)
Only use the following batteries and chargers with
this tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
Combined switch for on/o and speed control A 2
-control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Attaching belt clip 7
-attach the belt clip L to the drill with the supplied screw.
Battery level indicator 8
-press the battery level indicator button N to show the
current battery level.
Changing direction of rotation 9
-when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Changing bits q
! do not use bits with a damaged shank
Torque control (VariTorque) w
-output torque will increase as clutch ring B is rotated
from 1 to 17
-when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
-position F will lock up the clutch to permit (non-impact)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3020 in the language / languages: All languages as an attachment in your email.

The manual is 7,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info