757991
10
Zoom out
Zoom in
Previous page
1/132
Next page
1 0
C h anging direc t ion of rot at ion 9
-w h en not properly se t in left / righ t posi t ion, s w it c h A 2
c annot be ac t ivat ed
! change direction of rotation only when tool is at a
complete standstill
C h anging bit s q
! do not use bits with a damaged shank
Torq ue c ont rol ( VariTorq ue) w
-out put t orq ue w ill inc rease as c lut c h ring B is rot at ed
from 1 t o 1 7 ; posi t ion C w ill loc k up t h e c lut c h t o perm it
drilling or driving h eavy dut y w ork
-when turning in a screw, rst try VariTorque position 1
and inc rease unt il t h e desi red dept h h as been reac h ed
Mec h anic al gear se lec t ion e
-se t se lec t or D t o desi red sp eed
! actuate the gear selector while tool is running
slowly
1
-low sp eed
-h igh t orq ue
-for sc rew driving and drilling large diam et ers
-for t apping t h read
2
-h igh sp eed
-low er t orq ue
-for im pac t drilling
-for drilling sm all diam et ers
H olding and guiding t h e t ool t
! while working, always hold the tool at the grey-
coloured grip area(s)
-keep vent ilat ion sl ot s H 2 unc overed
-do not apply t oo m uc h pressu re on t h e t ool; let t h e t ool
do t h e w ork for y ou
APPLICATION ADVICE
U se t h e appropriat e bit s y
! only use sharp bits
W h en drilling ferrous m et als
-pre- drill a sm aller h ole, w h en a large h ole is req uired
-lubric at e drill bit oc c asi onally w it h oil
W h en t urning in a sc rew at / near t h e c ross c ut end or an
edge of w ood, pre- drill a h ole in order t o avoid c rac king
of t h e w ood
For an optimal use of the tool a steady pressure on the
sc rew is req uired, esp ec ially w h ile rem oving
W h en sc rew driving in h ard w ood one sh ould pre- drill a
h ole
Splint erfree drilling in w ood u
Dust free drilling in w alls i
Drilling in t iles w it h out ski dding o
For more information see www.skil.com
MAINTENANCE / SERVICE
Th is t ool is not int ended for professi onal use
Alw ay s keep t ool c lean ( esp ec ially vent ilat ion sl ot s H 2)
! remove battery from tool before cleaning
If t h e t ool sh ould fail desp it e t h e c are t aken in
m anufac t uring and t est ing proc edures , repair sh ould
be c arried out by an aft er- sa les se rvic e c ent re for SKIL
pow er t ools
-se nd t h e t ool undismantled t oget h er w it h proof of
purc h as e t o y our dealer or t h e nearest SKIL se rvic e
st at ion ( addresse s as w ell as t h e se rvic e diagram of t h e
t ool are list ed on w w w . ski l. c om )
full c apac it y of t h e bat t ery , c om plet ely c h arge t h e bat t ery
in t h e bat t ery c h arger before usi ng y our pow er t ool for t h e
rst time)
Only use the following batteries and chargers with
this tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use bat t ery w h en dam aged; it sh ould be replac ed
im m ediat ely
Do not disa sse m ble t h e bat t ery
Do not exp ose t ool/ bat t ery t o rain
Permitted ambient temperature (tool/charger/battery):
-w h en c h arging 4. . . 40° C
-during operat ion –2 0. . . + 50° C
-during st orage –2 0. . . + 50° C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 R ead t h e inst ruc t ion m anual before use
4 Batteries may explode when disposed of in re, so do not
burn bat t ery for any reaso n
5 St ore t ool/ c h arger/ bat t ery in loc at ions w h ere t em perat ure
w ill not ex c eed 50° C
6 Do not disp ose of elec t ric t ools and bat t eries t oget h er
w it h h ouse h old w ast e m at erial
USE
Combined switch for on/o and speed control A 2
-c ont rol t h e sp eed st eplessl y from z ero t o m axi m um by
put t ing less or m ore pressu re on t h e t rigger
C h arging bat t ery
! read the safety warnings and instructions
provided with the charger
R em oving/ inst alling t h e bat t ery 2
At t ac h ing belt c lip 7
-at t ac h t h e belt c lip J t o t h e drill w it h t h e su pplied sc rew .
Bat t ery level indic at or 8
-press t h e bat t ery level indic at or but t on K t o sh ow t h e
c urrent bat t ery level 8a
! when the lowest level of the battery indicator
8b, the
battery is empty
! 
after pressing button K 8c, the battery is not
within the allowable operating temperature range
LED- ligh t r
LED- ligh t aut om at ic ally ligh t s on w h en ac t ivat ing t h e on/
o switch
! 
protection is activated (see below)
Bat t ery prot ec t ion
The tool is suddenly being switched o or prevented from
being s w it c h ed on, w h en
-the load is too high - - > rem ove load and rest art
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C - - > 2
levels of the battery level indicator start ashing when
pressi ng but t on K 8c ; w ait unt il bat t ery h as ret urned
w it h in t h e allow able operat ing t em perat ure range
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
bat t ery level 8b is sh ow n by t h e bat t ery level indic at or
w h en pres si ng but t on K; c h arge bat t ery
! 

damaged
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3008 in the language / languages: All languages as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info