591182
8
Zoom out
Zoom in
Previous page
1/164
Next page
8
9 Do not dispose of the battery
together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG
(U.K. ONLY):
Do not connect the blue (= neutral) or
brown (= live) wire in the cord of the
charger to the earth terminal of the
plug
If for any reason the old plug is cut o
the cord of the charger, it must be
disposed of safely and not left
unattended
USE
Charging battery 0
- battery of new tools is not fully
charged
! unplug the charger from the
tool after charging period has
ended thereby lengthening the
service life of the battery
IMPORTANT:
- while charging, the charger and the
battery may become warm to
touch; this is normal and does not
indicate a problem
- do not charge at temperatures
below 0°C and over 45°C; this will
seriously damage the battery as
well as the charger
! a lithium-ion battery that is new
or has not been used for a
longer period does not develop
its full capacity until after
approximately 3 charging/
discharging cycles
- connect charger B with both wall
socket and contact C
- charging light D turns on indicating
that the tool is being charged
- when the battery is fully charged,
charging light D turns o (after
5 hours)
- the lithium-ion battery can be
charged at any time (interrupting
the charging procedure does not
damage the battery)
- the lithium-ion battery does not
have to be empty before charging
(no “memory-eect” as with
nickel-cadmium batteries)
- if you anticipate long periods of
non-use for the tool, it is best to
unplug the charger from its power
source
On/o !
Changing direction of rotation @
- when not properly set in left/right
position, the tool will not operate
! change direction of rotation
only when tool is at a complete
standstill
Changing bits #
- push bit to end position in bitholder
! do not use bits with a damaged
shank
Automatic spindle-lock
Allows you to manually tighten or
loosen screws, when necessary $
Spot light G %
Spot light G automatically lights on
when activating switch A 2
Two handle positions ^
Battery protection
Switches o the tool automatically
when
1) the load is too high
2) the battery temperature is not
within the allowable operating
temperature range of -10 to +60°C
3) the lithium-ion battery is nearly
empty (to protect against deep
discharge)
! do not continue to press the on/
off switch after the tool is
switched off automatically;
battery may be damaged
APPLICATION ADVICE
Use the appropriate bits &
! do not use damaged bits
! only use bits with hexagon shaft
When turning in a screw at/near the
cross cut end or an edge of wood,
pre-drill a hole in order to avoid
cracking of the wood
For an optimal use of the tool a steady
pressure on the screw is required,
especially while removing
When screwdriving in hard wood one
should pre-drill a hole
For more tips see www.skileurope.com
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 2536 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2536 in the language / languages: All languages as an attachment in your email.

The manual is 7,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info