Manual Skil 2531 AB (page 9 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

489021

Zoom out

Zoom in

1/132

8 Do not dispose of the charger together with household

waste material

9 Do not dispose of the battery together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not

left unattended

USE

• Combined switch A 2 for on/o and speed control

Control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery 0

! a lithium-ion battery that is new or has not been

used for a longer period does not develop its full

capacity until after approximately 3 charging/

discharging cycles

- connect charger to power source as illustrated 0a

- green light B will turn on indicating that the charger is

ready for operation 0a

- insert battery into charger as illustrated 0b

! the battery can also remain in the tool while

charging; in that case the tool cannot be

switched on

- green light B will blink indicating that the battery is

being charged 0c

- after approximately 1 hour the battery is fully charged

and green light B stays on after blinking, at which time

the charger automatically switches to maintenance-

charging 0d

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- if green light B does not blink after inserting a battery,

this may mean that the battery is too cold or too hot

(charger only charges batteries when its temperature

is between 0°C and 45°C); the charger then

automatically switches to maintenance-charging, until

a temperature between 0°C and 45°C is reached, at

which time the charger will automatically switch to

normal charging 0e

- the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not damage

the battery)

- the lithium-ion battery does not have to be empty

before charging (no “memory-eect” as with

nickel-cadmium batteries)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

- when the lithium-ion battery is empty, the tool is

switched o automatically

- a signicantly reduced working period after charging

indicates that the battery is worn out and should

be replaced

• Changing direction of rotation !

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits @

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) #

- output torque will increase as clutch ring C is rotated

from 1 to 19; position D will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection $

- set selector F to desired speed

! actuate the gear selector while tool is

running slowly

LOW

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

HIGH

- high speed

- lower torque

- for drilling small diameters

• Battery protection

Switches o the tool automatically when

1) the load is too high

2) the battery temperature is not within the allowable

operating temperature range of -10 to +60°C

3) the lithium-ion battery is nearly empty (to protect

against deep discharge)

! do not continue to press the on/off switch after

the tool is switched off automatically; battery may

be damaged

• Spot light G %

Spot light G automatically lights on when activating

switch A 2

• Holding and guiding the tool ^

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots H 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits &

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2531 AB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 2531 AB Manual

Product: