Manual Skil 2511 (page 10 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

479929

Zoom out

Zoom in

1/120

EXPLANATION OF SYMBOLS ON CHARGER/BATTERY

3 Read the instruction manual before use

4 Only use the charger indoors

5 Double insulation (no earth wire required)

6 Automatic shut-off when charger gets too hot (thermic

fuse blows and charger becomes useless)

7 Incorrect polarity of the charger connection could cause a

hazard (only charge the battery with the charger supplied)

8 Do not dispose of the charger together with household

waste material

9 Do not dispose of the battery together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not

left unattended

USE

• Charging battery 0

- battery of new tools is not fully charged

- connect charger to power source as illustrated

- insert battery into charger

- red light L will turn on indicating that the battery is

being charged

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- after 3 hours the charging operation will be completed,

and the battery may be used, even though the red

light may still be on (the red light may require more

than 3 hours to turn o)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

! a battery that is new or has not been used

for a longer period does not develop its full

capacity until after approximately 5 charging/

discharging cycles

- do not repeatedly recharge the battery after only a few

minutes of operation; this may result in a reduction of

operating time and battery eciency

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

• On/o !

• Speed control for smooth starting @

• Changing direction of rotation #

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits $

- push bit to end position in bitholder G

! do not use bits with a damaged shank

• Torque control (VariTorque) %

- limits the amount of output torque delivered by the

chuck (6 clutch settings)

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Screwbit identication and storage ^

Identies and stores the right bit for a awless screwdriving job

• Holding and guiding the tool &

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots J 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits *

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill

a hole

• Splinterfree drilling in wood (

• Dustfree drilling in walls )

• Dustfree drilling in ceilings ¡

• Drilling in tiles without skidding ™

• For more tips see www.skileurope.com

MAINTENANCE / SERVICE

• Keep tool and charger clean

- clean charging contacts in charger with alcohol or

contact cleaner

! unplug charger from power source before

cleaning

• If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skileurope.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 8 will remind you of this when the need for

disposing occurs

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2511 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 2511 Manual

Product: