Manual Skil 2401 (page 8 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

479919

Zoom out

Zoom in

1/100

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the

plug

• If for any reason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left

unattended

USE

• Charging battery 5

- battery of new tools is not fully charged

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- after 3 hours the charging operation will be

completed, and the battery may be used, even

though the red light may still be on (the red light

may require more than 3 hours to turn off)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well

as the charger

- do not remove battery from tool while it is running

! a battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles

- do not repeatedly recharge the battery after only a

few minutes of operation; this may result in a

reduction of operating time and battery efﬁ ciency

- the nickel-cadmium battery must be kept separate

from the natural environment and should not be

disposed of as normal domestic waste (symbol 6

will remind you of this when the need for disposing

occurs)

! prior to disposal protect battery terminals with

heavy tape to prevent short-circuit

- if you anticipate long periods of non-use for the tool,

it is best to unplug the charger from its power source

• On/off 7

• Speed control for smooth starting 8

• Changing direction of rotation 9

- when not properly set in left/right position, switch

A 2 cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits 0

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) !

- limits the amount of output torque delivered by the

chuck (6 clutch settings)

- when turning in a screw, ﬁ rst try VariTorque position 1

and increase until the desired depth has been

reached

• Holding and guiding the tool @

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

APPLICATION ADVICE

• Use the appropriate bits #

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill a

hole

• Splinterfree drilling in wood $

• Dustfree drilling in walls %

• Dustfree drilling in ceilings ^

• Drilling in tiles without skidding &

• For more tips see www.skileurope.com

GUARANTEE / ENVIRONMENT

• Keep tool and charger clean

- the charger may be cleaned most effectively with

compressed air (wear safety goggles)

- clean charging contacts in charger with alcohol or

contact cleaner

! unplug charger from power source before

cleaning

• This SKIL product is guaranteed in accordance with

statutory/country-speciﬁ c regulations; damage due to

normal wear and tear, overload or improper handling will

be excluded from the guarantee

• In case of a complaint, send the tool or charger

undismantled together with proof of purchase to your

dealer or the nearest SKIL service station (addresses as

well as the service diagram of the tool are listed on

www.skileurope.com)

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol * will remind you of this when the need for

disposing occurs

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2401 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 2401 Manual

Product: