591176
8
Zoom out
Zoom in
Previous page
1/128
Next page
8
- for screwdriving and drilling large diameters
- for tapping thread
HIGH
- high speed
- lower torque
- for drilling small diameters
 Battery level indicator C
t
- indicates the charge condition of the battery for a few
seconds when switch D
2
is pressed half or fully
through
- consists of a two-colour LED
- continuous lighting, green : 33-100%
- continuous lighting, red : 11-33%
- ashing light, red : < 11%
 Spot light
y
Spot light L automatically lights on when activating
switch D
2
 Holding and guiding the tool
! 
coloured grip area(s)
u
- keep ventilation slots M
2
uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
 When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
 When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
 For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
 When screwdriving in hard wood one should pre-drill a
hole
 For more tips see www.skil.com
MAINTENANCE / SERVICE
 This tool is not intended for professional use
 Keep tool and charger clean
! unplug charger from power source before
cleaning
 If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
- in case of a defective charger send both charger and
tool to your dealer or the SKIL service station
ENVIRONMENT
 Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
EXPLANATION OF SYMBOLS ON TOOL/CHARGER
3
Read the instruction manual before use
4
Only use the charger indoors
5
Double insulation (no earth wire required)
6
Do not dispose of the charger together with household
waste material
7
Do not dispose of the battery together with household
waste material
USE
 Charging battery
2
- connect charger A with both wall socket and contact B
- indicator C starts blinking GREEN indicating that the
battery is being charged
- after 3 hours the battery is fully charged and charging
automatically stops (green light stays on after blinking)
- if the tool is used only briey, the charging time can be
very short
- unplug the charger when the battery is fully charged
IMPORTANT:
- if indicator C starts blinking RED, this may mean that
the battery is too cold or too hot; when the battery
temperature returns to between 0°C and 45°C, the
charger will automatically begin charging
- the lithium-ion battery can be charged at any time
(interrupting the charging procedure does not damage
the battery)
- while charging, tool and charger may become warm to
touch; this is normal and does not indicate a problem
 Battery protection
Switches o the tool or reduces the speed automatically
when
- the load is too high
- the battery is empty
! 

be damaged
 On/O
8
 Speed control for smooth starting
9
 Changing direction of rotation
q
- indicator F shows the selected direction of rotation
- when not properly set in left/right position, switch D
2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
 Changing bits
w
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
! only use sharp bits
 Torque control (VariTorque)
e
- output torque will increase as clutch ring H is rotated
from 1 to 17; position J will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
 Mechanical gear selection
r
(2330)
- set selector K to desired speed
! actuate the gear selector while tool is running
slowly
LOW
- low speed
- high torque
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 2330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2330 in the language / languages: All languages as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info