644733
8
Zoom out
Zoom in
Previous page
1/136
Next page
8
5 Double insulation (no earth wire required)
6 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
7 Store tool/charger/battery in locations where temperature
will not exceed 50°C
8 Do not dispose of the charger together with household
waste material
9 Do not dispose of the battery together with household
waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the plug
If for any reason the old plug is cut o the cord of the
charger, it must be disposed of safely and not left
unattended
USE
Combined switch A 2 for on/o and speed control
Control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
Charging battery 0
- connect charger to power source as illustrated
- green light B will turn on indicating that the charger is
ready for operation 0a
- insert battery into charger as illustrated 0b
! the battery can also remain in the tool while
charging; in that case the tool cannot be switched
on
- green light B will blink indicating that the battery is
being charged 0c
- after approximately 1 hour the battery is fully charged
and green light B stays on after blinking 0d
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- if green light B does not blink after inserting a battery,
this may mean:
1) that the battery is too cold or too hot (charger only
charges batteries when its temperature is between
0°C and 45°C)
2) that the battery should be replaced
- the lithium-ion battery can be charged at any time
(interrupting the charging procedure does not damage
the battery)
- the lithium-ion battery does not have to be empty
before charging (no “memory-eect” as with
nickel-cadmium batteries)
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
45°C; this will seriously damage the battery as well as
the charger
- do not remove battery from tool while it is running
- if you anticipate long periods of non-use for the tool, it
is best to unplug the charger from its power source
- when the lithium-ion battery is empty, the tool is
switched o automatically
- a signicantly reduced working period after charging
indicates that the battery is worn out and should be
replaced
Changing direction of rotation !
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Changing drill bits @
- insert the bit as deep as possible in the chuck
- use screw bits in combination with a bitholder
! do not use bits with a damaged shank
! only use sharp bits
Torque control (VariTorque) #
- output torque will increase as clutch ring C is rotated
from 1 to 15; position D will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
Mechanical gear selection $
- set selector F to desired speed
! actuate the gear selector while tool is running
slowly
HIGH POWER
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
HIGH SPEED
- lower torque
- for drilling small diameters
Battery level indicator %
- shows how much energy the battery has left
- indicator G automatically lights on when activating
switch A 2
Spot light H ^
Spot light H automatically lights on when activating
switch A 2
Battery protection
Switches o the tool automatically when
1) the load is too high
2) the battery temperature is not within the allowable
operating temperature range of -10 to +60°C
3) the lithium-ion battery is nearly empty (to protect
against deep discharge)
- in either case the 3 LED-lights of battery level indicator
G will ash rapidly
! do not continue to press the on/off switch after
the tool is switched off automatically; battery may
be damaged
Automatic spindle-lock
- when switch A 2 is not pressed, the spindle is locked
- allows you to use the tool as a screwdriver (even when
the battery is empty)
Holding and guiding the tool &
! while working, always hold the tool at the
grey-coloured grip area(s)
- keep ventilation slots J 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 2244 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2244 in the language / languages: All languages as an attachment in your email.

The manual is 8,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info