644737
8
Zoom out
Zoom in
Previous page
1/128
Next page
8
6 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
7 Store tool/charger/battery in locations where temperature
will not exceed 50°C
8 Do not dispose of the charger together with household
waste material
9 Do not dispose of the battery together with household
waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the plug
If for any reason the old plug is cut o the cord of the
charger, it must be disposed of safely and not left
unattended
USE
On/o 0
Speed control for smooth starting !
Charging battery @
- connect charger to power source as illustrated
- green light B will turn on indicating that the charger is
ready for operation @a
- insert battery into charger as illustrated @b
- green light B will blink indicating that the battery is
being charged @b
- after approximately 1 hour the battery is fully charged
and green light B stays on after blinking @c
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- if green light B does not blink after inserting a battery,
this may mean:
1) that the battery is too cold or too hot (charger only
charges batteries when its temperature is between
0°C and 45°C)
2) that the battery should be replaced
- the lithium-ion battery can be charged at any time
(interrupting the charging procedure does not damage
the battery)
- the lithium-ion battery does not have to be empty
before charging (no “memory-eect” as with
nickel-cadmium batteries)
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not remove battery from tool while it is running
- a signicantly reduced working period after charging
indicates that the battery is worn out and should be
replaced
Changing direction of rotation #
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Changing drill bits $
- insert the bit as deep as possible in the chuck
- use screw bits in combination with a bitholder
! do not use bits with a damaged shank
! only use sharp bits
Torque control (VariTorque) %
- output torque will increase as clutch ring C is rotated
from 1 to 19; position D will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
Spot light F ^
Spot light F automatically lights on when activating switch
A 2
Battery protection
Switches o the tool automatically when
1) the load is too high
2) the battery temperature is not within the allowable
operating temperature range of -10 to +60°C
3) the lithium-ion battery is nearly empty (to protect
against deep discharge)
! do not continue to press the on/off switch after
the tool is switched off automatically; battery may
be damaged
Holding and guiding the tool &
! while working, always hold the tool at the
grey-coloured grip area(s)
- keep ventilation slots G 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
When screwdriving in hard wood one should pre-drill a
hole
MAINTENANCE / SERVICE
Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skilmasters.com)
- in case of a defective charger send both charger and
battery to your dealer or the SKIL service station
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 2108 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2108 in the language / languages: All languages as an attachment in your email.

The manual is 8,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info