591179
9
Zoom out
Zoom in
Previous page
1/128
Next page
9
APPLICATION ADVICE
 Use the appropriate bits
o
! only use sharp bits
 When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
 When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
 For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
 When screwdriving in hard wood one should pre-drill a
hole
 Splinterfree drilling in wood
p
 Dustfree drilling in walls
a
 Dustfree drilling in ceilings
s
 Drilling in tiles without skidding
d
 For more tips see www.skil.com
MAINTENANCE / SERVICE
 This tool is not intended for professional use
 Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
 If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
- in case of a defective charger send both charger and
battery to your dealer or the SKIL service station
ENVIRONMENT
 Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol
9
will remind you of this when the need for
disposing occurs
 The battery must be kept separate from the natural
environment and should not be disposed of as normal
domestic waste (symbol
q
will remind you of this when
the need for disposing occurs)
! prior to disposal protect battery terminals with

9
Do not dispose of the charger together with household
waste material
q
Do not dispose of the battery together with household
waste material
USE
 Charging battery
w
- battery of new tools is not fully charged
- connect charger to power source as illustrated
- green light G will turn on indicating that the charger is
ready for operation
- insert battery into charger
- red light H will turn on indicating that the battery is
being charged
- charge the battery for at least 5 hours, after which
the battery may be used even though the red light
may still be on (the red light may require more than 5
hours to turn o)
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well as
the charger
- do not remove battery from tool while it is running
! a battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles
- do not repeatedly recharge the battery after only a few
minutes of operation; this may result in a reduction of
operating time and battery eciency
- if you anticipate long periods of non-use for the tool, it
is best to unplug the charger from its power source
 On/o
e
 Speed control for smooth starting
r
 Changing direction of rotation
t
- when not properly set in left/right position, switch A
2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
 Changing bits
y
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
 Torque control (VariTorque)
u
- limits the amount of output torque delivered by the
chuck (21 clutch settings)
- when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
 Holding and guiding the tool
i
! 
coloured grip area(s)
- keep ventilation slots E
2
uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2017 in the language / languages: All languages as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info