479912
9
Zoom out
Zoom in
Previous page
1/120
Next page
9
EXPLANATION OF SYMBOLS ON CHARGER/BATTERY
3 Read the instruction manual before use
4 Only use the charger indoors
5 Double insulation (no earth wire required)
6 Fail-safe isolating transformer (the power source is
electrically separated from the transformer output)
7 Automatic shut-off when charger gets too hot (thermic
fuse blows and charger becomes useless)
8 Incorrect polarity of the charger connection could
cause a hazard (only charge the battery with the
charger supplied)
9 Do not dispose of the charger together with household
waste material
0 Do not dispose of the battery together with household
waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the plug
If for any reason the old plug is cut o the cord of the
charger, it must be disposed of safely and not left
unattended
USE
Charging battery !
- battery of new tools is not fully charged
- connect charger to power source as illustrated
- green light G will turn on indicating that the charger is
ready for operation
- insert battery into charger
- red light H will turn on indicating that the battery is
being charged
- red light H will stay on as long as the battery is
connected to the charger and the charger is in the wall
socket
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- after 3-5 hours the charging operation will be
completed, and the battery may be used
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well as
the charger
- do not remove battery from tool while it is running
! a battery that is new or has not been used
for a longer period does not develop its full
capacity until after approximately 5 charging/
discharging cycles
- do not repeatedly recharge the battery after only a few
minutes of operation; this may result in a reduction of
operating time and battery eciency
- if you anticipate long periods of non-use for the tool, it
is best to unplug the charger from its power source
On/o @
Changing direction of rotation #
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
Changing bits $
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
Torque control (VariTorque) %
- limits the amount of output torque delivered by the
chuck (21 clutch settings)
- when turning in a screw, rst try VariTorque position 1
and increase until the desired depth has been reached
Holding and guiding the tool ^
! while working, always hold the tool at the
grey-coloured grip area(s)
- keep ventilation slots E 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
Use the appropriate bits &
! only use sharp bits
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
When screwdriving in hard wood one should pre-drill a
hole
Splinterfree drilling in wood *
Dustfree drilling in walls (
Dustfree drilling in ceilings )
Drilling in tiles without skidding ¡
For more tips see www.skileurope.com
MAINTENANCE / SERVICE
Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source
before cleaning
If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skileurope.com)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 2006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2006 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info