758621
7
Zoom out
Zoom in
Previous page
1/120
Next page
7
for improved visualisation of the
laser beam, but they do not protect
against laser radiation)
-do not use the laser viewing
glasses as sun glasses or in
 (the laser viewing glasses do
not aord complete UV protection
and reduce colour perception)
Working with the tripod (not standard
included)
-tripod K 1 oers a stable, height-
adjustable measuring support
-place the measuring tool via tripod
mount G onto the 1/4” male thread
of the tripod and screw the locking
screw of the tripod tight
MAINTENANCE / SERVICE
This tool is not intended for
professional use
Protect the measuring tool against
moisture and direct sun light
Do not subject the measuring
tool to extreme temperatures or
variations in temperature (the
accuracy of the measuring tool can
be impaired)
-as an example, do not leave it in
vehicles for long time
-allow the measuring tool to adjust
to the ambient temperature before
putting it into operation
Avoid heavy impact to or falling
down of the measuring tool
-damage to the measuring tool can
impair its accuracy
-after heavy impact or shock,
compare the laser lines with
a known horizontal or vertical
reference line
Push switch F 1 into locking
position 6 when transporting
the measuring tool (this locks the
levelling unit, which can be damaged
in case of intense movement)
Keep the measuring tool clean at all
times
Do not immerse the measuring tool in
water or other uids
Wipe o debris using a moist and
soft cloth
Do not use any cleaning agents or
solvents
-slide switch F to position 6a
-if the automatic levelling function
is not possible, e.g. because the
surface on which the measuring tool
stands deviates by more than 4°
from the horizontal plane, the laser
lines ash and indicator E turns red
-if this is the case, set up the
measuring tool in a level position
and wait for the self-levelling to
take place
-as soon as the measuring tool is
once again within the self-levelling
range of ±4°, the laser lines light
up continuously and indicator E
turns o
-when not within the self-levelling
range of ±4°, working with automatic
levelling is not possible, because
it cannot be assured that the laser
lines run at a right angle to each
other
-in case of ground vibrations or
position changes during operation,
the measuring tool is automatically
levelled in again
-to avoid errors, check the position of
the horizontal and vertical laser line
with regard to the reference points
upon re-levelling
Working without automatic levelling
-slide switch F to position 6b
-push laser button C to turn on the
laser beam
-indicator E turns red continuously
in this mode
-when automatic levelling is switched
o, you can hold the measuring tool
freely in your hand or place it on an
inclined surface
APPLICATION ADVICE
Always use the centre of the laser
line for marking (the width of the
laser line changes with the distance)
Laser viewing glasses 1 (not
standard included)
-laser viewing glasses J 1 lter out
the ambient light
-this makes the light of the laser
appear brighter for the eyes
-do not use the laser viewing
glasses as safety goggles (the
laser viewing glasses are used
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 1961 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1961 in the language / languages: All languages as an attachment in your email.

The manual is 3,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info