Manual Skil 1840 AA (page 8 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

482559

Zoom out

Zoom in

1/128

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR ROUTERS

GENERAL

• Thistoolshouldnotbeusedbypeopleundertheageof

16 years

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

ACCESSORIES

• SKILcanassureawlessfunctioningofthetoolonly

when original accessories are used

• Useonlyaccessorieswithanallowablespeedmatching

at least the highest no-load speed of the tool

• Donotusedamagedordeformedrouterbits

• Onlyusesharprouterbits

• Protectaccessoriesfromimpact,shockandgrease

• Onlyusehighspeedsteel(HSS)orcarbide-tipped(CT)

router bits with this tool

BEFORE USE

• Avoiddamagethatcanbecausedbyscrews,nailsand

otherelementsinyourworkpiece;removethembefore

you start working

• Alwayscheckthatthesupplyvoltageisthesameasthe

voltageindicatedonthenameplateofthetool(tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Use clamps or another practical way to secure and

support the workpiece to a stable platform (holding

theworkbyyourhandoragainstthebodyleavesit

unstable and may lead to loss of control)

• Donotclampthetoolinavice

• Usecompletelyunrolledandsafeextensioncordswith

a capacity of 16 Amps (U.K. 13 Amps)

• Thenoiselevelwhenworkingcanexceed85dB(A);

wear ear protection

• Dustfrommaterialsuchaspaintcontaininglead,some

woodspecies,mineralsandmetalmaybeharmful

(contact with or inhalation of the dust may cause

allergic reactions and/or respiratory diseases to the

operator or bystanders); wear a dust mask and work

with a dust extraction device when connectable

• Certainkindsofdustareclassiedascarcinogenic(such

as oak and beech dust) especially in conjunction with

additivesforwoodconditioning;wear a dust mask and

work with a dust extraction device when connectable

• Followthedust-relatednationalrequirementsforthe

materials you want to work with

• Besuretoolisswitchedoffwhenpluggingin

DURING USE

• Hold power tool by insulated gripping surfaces,

because the cutter may contact its own cord (cutting

a“live”wiremaymakeexposedmetalpartsofthe

powertool“live”andshocktheoperator)

• Alwayskeepthecordawayfrommovingpartsofthe

tool;directthecordtotherear,awayfromthetool

• Neverusethetoolwhencordorbase-plateR2

(=protectiveguard)isdamaged;haveitreplacedbya

qualiedperson

• Keephandsandngersawayfromrouterbitwhentool

is switched on

• Neverexceedmaximumcuttingdepthofrouterbit

while cutting

• Incaseofelectricalormechanicalmalfunction,

immediately switch off the tool and disconnect the plug

• Incasetherouterbitisblocked,resultinginjerking

forcesonthetool,immediatelyswitchoffthetool

• Incaseofcurrentinterruptionorwhentheplugis

accidentallypulledout,immediatelyswitchoffthetool

inordertopreventuncontrolledrestarting

• Donotapplysomuchpressureonthetoolthatitcomes

to a standstill

AFTER USE

• Afternishingthework,loosenleverH2,guidethetool

backintotheupperstartingposition,andswitchoffthetool

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Donotconnecttheblue(=neutral)orbrown(=live)wire

in the cord of this tool to the earth terminal of the plug

• Ifforanyreasontheoldplugiscutoffthecordofthis

tool,itmustbedisposedofsafelyandnotleftunattended

USE

• Mounting/removingrouterbits4

! switch off the tool and disconnect the plug

! ensure that router bit shaft is perfectly clean

! ensure that collet size (6 mm, 8 mm) corresponds

with shaft size of router bit

- turn tool upside down

- lockshaftbypushingshaftlockA(rotatecolletnutB,

if necessary) and hold it while you

FOR MOUNTING:

- loosen collet nut B with wrench C

- insert bit 3/4 in collet

- tightencolletnutrmlywithwrenchC

FOR REMOVING:

- loosen collet nut B with wrench C

- removebit

- release shaft lock A

! for loosening router bit it may be necessary to tap

collet nut with wrench 5

! never tighten collet nut, if there is no router bit in

collet; collet may be damaged

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1840 AA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 1840 AA Manual

Product: