758386
11
Zoom out
Zoom in
Previous page
1/120
Next page
11
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
Splinterfree drilling in wood t
Dustfree drilling in walls y
Dustfree drilling in ceilings u
Drilling in tiles without skidding i
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Never open the tool yourself o
Always keep tool and cord clean (especially ventilation
slots H 2)
! disconnect the plug before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Do not dispose of electric tools, accessories and

(only for EU countries)
-in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
-symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
Measured in accordance with EN 60745 the sound
pressure level of this tool is 94.0 dB(A) and the sound
power level 105.0 dB(A) (uncertainty K = 3 dB), and the
vibration (triax vector sum; uncertainty K = 1.5 m/s²)
when hammer drilling in concrete 18.7 m/s²
when chiseling 20.3 m/s²
The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
-using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
-the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! 
maintaining the tool and its accessories, keeping

patterns
-press button C to unlock switch D
-rst turn switch D to the desired operating mode until it
snap-locks
-then turn switch E to the desired operating mode
1 = normal drilling/screwdriving
2 = impact drilling
3 = chiseling
! 
-for drilling in wood, metal and plastic as well as for
screwdriving the corresponding adapter should be
used (see: Application Advice)
-the hammer mechanism is activated by applying a
slight pressure on the tool when the drill bit is in contact
with the workpiece
-it takes a short time for the hammer mechanism to
reach full impact power
-do not apply too much pressure on the tool; let the tool
do the work for you
Changing bits 9
! clean and lightly lubricate the SDS+ accessory
before insertion
-pull back locking sleeve F and insert accessory
in SDS+ chuck while turning and pushing it until it
engages; the accessory locks in position automatically
-pull accessory to check that it is locked correctly
-remove accessory by pulling back locking sleeve F
! the SDS+ accessory requires freedom of



drilling precision
! 
Safety clutch
if the accessory gets jammed, the drive to the spindle is
interrupted (causing a rattling noise)
-immediately switch o tool
-remove the jammed accessory
-switch on tool again
Adjusting drilling depth q
Holding and guiding the tool w
! 
coloured grip area(s)
- (can be adjusted as
illustrated)
-keep ventilation slots H 2 uncovered
APPLICATION ADVICE
Use the appropriate bits e
! only use sharp bits/chisels
For drilling in wood, metal and plastic as well as for
screwdriving use the corresponding adapter r
-clean and lightly lubricate adapter before insertion
-pull back locking sleeve F 2 and insert adapter
in SDS+ chuck while turning and pushing it until it
engages; the adapter locks in position automatically
-pull adapter to check whether is it locked correctly
-set switch D 2 to normal drilling (
)
When drilling ferrous metals
-pre-drill a smaller hole, when a large hole is required
-lubricate drill bit occasionally with oil
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 1781 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1781 in the language / languages: All languages as an attachment in your email.

The manual is 7,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info