758610
10
Zoom out
Zoom in
Previous page
1/116
Next page
10
mask and work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
SKIL can assure awless functioning of the tool only
when original accessories are used
Never use the tool when the cord is damaged; it must be
replaced by a specially prepared cord available through
the service organization.
Always disconnect plug from power source before
making any adjustment or changing any accessory
BEFORE USE
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Before using the tool check that the knives do not brush
anywhere
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
Keep your ngers away from the rotating knives
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
If any chip should get jammed in the chip outlet, you
should switch o the motor, ensure that all moving parts
have come to a complete standstill, disconnect the plug,
and remove the jammed chip
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Changing/reversing knives 6
This planer is equipped with non-grindable knives with
cutting edges on both sides; so if one side has become
blunt, the other side can be used
! 
-remove guiding devices, if mounted
-take wrench from storage A 6 a
-turn tool upside down
-loosen 3 bolts B with wrench (do not remove bolts) 6 b
-push knife out of cutter block with piece of wood 6 c
-put knife back in cutter block in reversed position, or
use new knife 6 d
! groove in knife should match ledge in cutter block
! place knives against support plate R 6 e
-rmly tighten 3 bolts B with wrench 6 f
! change/reverse knives in time; only use sharp
knives
! always change/reverse both knives at the same
time
 Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage

power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) 
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR PLANERS
Wait for the cutter to stop before setting the tool
down (an exposed rotating cutter may engage the
surface leading to possible loss of control and serious
injury)
Hold the power tool by insulated gripping surfaces,
because the cutter may contact its own cord (cutting
a “live” wire may make exposed metal parts of the power
tool “live”and could give the operator an electric shock)
Use clamps or another practical way to secure and
support the workpiece to a stable platform (holding
the workpiece by your hand or against the body leaves it
unstable and may lead to loss of control)
GENERAL
This tool should not be used by people under the age of
16 years
The noise level when working can exceed 85 dB(A);
wear ear protection
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 1590 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1590 in the language / languages: All languages as an attachment in your email.

The manual is 6,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info