Manual Skil 1490 - MULTI-FUNCTION TOOL (page 7 of 112) (All languages)

644811

Zoom out

Zoom in

1/112

- check the tight seating of the accessory (incorrect

or not securely fastened accessories can come loose

during operation and create a hazard)

• Mounting of sanding sheet 5

- knock the dust out of the VELCRO material on sanding

pad C 2 before mounting the sanding sheet

- mount VELCRO sanding sheet as illustrated

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total VELCRO

surface covered with sanding paper

• Dust/chip extraction 6

- mount dust extraction device D as illustrated

- connect vacuum cleaner

! do not use dust extraction device/vacuum cleaner

when sanding metal

- clean dust extraction device D regularly for optimal

dust pick-up performance

• On/o

- switch on/o the tool by pushing switch E 2 in "I"/"O"

position

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

• Adjusting working speed 7

- with wheel F the required oscillating frequency can be

adjusted from low (1) to high (6) (also while tool is

running)

- the optimal working speed depends on the material

and can be determined with practical trials

• Holding and guiding the tool

! while working, always hold the tool at the

grey-coloured grip area(s) 8

- keep ventilation slots G 2 uncovered

- do not apply too much presssure on the tool

(excessive pressure will cause excessive heat and

may shorten the service life of the accessory)

APPLICATION ADVICE

• Use segment saw blade H 2 for separating and plunge

cuts in wood, plaster, gypsum and plastics (also for

sawing close to edges, in corners and other hard-to-

reach areas)

• Use plunge-cut saw blade J 2 for separating and deep

plunge cuts in ferrous and non-ferrous metals

• Use plunge-cut saw blade K 2 for smaller separating

and plunge cuts in ferrous and non-ferrous metals

• Use plunge-cut saw blade L 2 for separating and deep

plunge-cuts in wood, plaster, gypsum and soft plastics

(also for sawing close to edges, in corners and other

hard-to-reach areas)

• Use plunge-cut saw blade M 2 for smaller separating

and plunge-cuts in wood, plaster, gypsum and soft

plastics

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially ventilation

slots G 2)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skilmasters.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 9 will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product

described under “Technical data” is in conformity with the

following standards or standardization documents: EN

60745, EN 61000, EN 55014, in accordance with the

provisions of the directives 2004/108/EC, 2006/42/EC,

2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

¹ÊÁÂÆÎ¹Æ¼½ÊÇÇ¾¼½Æ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

Ä¹¾ÁÂÃ¿Ê¹¹¾

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

05.09.2014

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 85 dB(A) and the sound

power level 96 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (hand-arm method)

✱ when surface grinding 4.1 m/s² (uncertainty K = 1.5 m/s²)

✱ when cutting with plunge-cut saw blade 7.4 m/s²

(uncertainty K = 1.5 m/s²)

✱ when cutting with segment saw blade 7.1 m/s²

(uncertainty K = 1.5 m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1490 - MULTI-FUNCTION TOOL in the language / languages: All languages as an attachment in your email.

The manual is 8,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 1490 - MULTI-FUNCTION TOOL Manual

Product: