Manual Skil 1480 Multitool (page 12 of 116) (All languages)

701638

Zoom out

Zoom in

1/116

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Changing accessories 7

! disconnect the plug

- remove/mount the required accessory as illustrated

- ensure that the openings of the accessory engage into

the tabs of the tool head (any snap-in position

possible)

- mount the accessory with the depressed centre

pointing downwards

- take hex key A from storage B 2

- loosen/fasten screw C with hex key A

- check the tight seating of the accessory (incorrect

or not securely fastened accessories can come loose

during operation and create a hazard)

• Mounting of sanding sheet 8

- tap the dust out of the VELCRO material on sanding

pad D before mounting the sanding sheet

- mount VELCRO sanding sheet E as illustrated

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total VELCRO

surface covered with sanding paper

• Mounting of auxiliary handle F 9 (1480)

! disconnect the plug

- screw auxiliary handle F on the right or the left of the

tool (depending on the work to be carried out)

• Dust suction 0

! disconnect the plug

- use dust extraction device G only when working with

sanding pad D

- mount dust extraction device G as illustrated

- connect vacuum cleaner

! do not use dust extraction device/vacuum cleaner

when sanding metal

- clean dust extraction device G regularly for optimal

dust pick-up performance

• On/o

- switch on/o the tool by pushing switch H 2 in “I”/”O”

position

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

• Adjusting working speed !

- with wheel J the required oscillating frequency can be

adjusted from low (1) to high (6) (also while tool is

running)

- the optimal working speed depends on the material

and can be determined with practical trials

• Holding and guiding the tool

! while working, always hold the tool at the

grey-coloured grip area(s) @

- keep ventilation slots K uncovered

- do not apply too much pressure on the tool (excessive

pressure will cause excessive heat and may shorten the

service life of the accessory)

• Depth adjustment accessory (DEPTH STOP) (not

standard included) #

APPLICATION ADVICE

• For optimal results on dierent materials use table $ as

reference for determining the right accessory (accessories

not standard included)

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation slots

K 2)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law, electric

tools that have reached the end of their life must be

collected separately and returned to an environmentally

compatible recycling facility

- symbol 6 will remind you of this when the need for

disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound

pressure level of this tool is 91.0 dB(A) and the sound power

level 102.0 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)

✱ when sanding 4.5 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 62841; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when using

the tool for the applications mentioned

- using the tool for dierent applications, or with dierent or

poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1480 Multitool in the language / languages: All languages as an attachment in your email.

The manual is 5,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 1480 Multitool Manual

Product: