Manual Skil 1415 AC (page 10 of 172) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

482561

Zoom out

Zoom in

1/172

• Never use grinding discs over 32 mm (1 1/4”) Ø

• Never use drill bits over 3.2 mm (1/8”) Ø

• Never use a cutting disc for side grinding

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Secure the workpiece (a workpiece clamped with clamping

devices or in a vice is held more securely than by hand)

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Wear protective glasses and hearing protection 4,

protective gloves and sturdy shoes; when necessary, also

wear an apron

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful (contact

with or inhalation of the dust may cause allergic reactions

and/or respiratory diseases to the operator or bystanders);

wear a dust mask and work with a dust extraction

device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Ensure that the collet size corresponds with the shaft size

of the accessory

• Be sure tool is switched o when plugging in

DURING USE

• Use auxiliary handle(s), if supplied with the tool

(loss of control can cause personal injury)

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord (a cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock)

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Never use spindle lock while tool is running (damage

due to improper handling will be excluded from the

guarantee)

• Keep hands away from rotating accessories

• When grinding metal, sparks are generated; keep other

persons and combustible material from work area

• Keep the ventilation slots uncovered while working

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTER USE

• The accessory continues to rotate for a short time after

the tool has been switched o

• Before you put down the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• After switching o the tool, never stop the rotation of the

accessory by a force applied against it

• Store tool in locations where temperature will not

exceed 50°C

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool, it

must be disposed of safely and not left unattended

USE

• Changing accessories 5

! switch off the tool and disconnect the plug

! ensure that collet size corresponds with shaft

size of accessory

- push spindle-lock button B and hold it while you turn

collet nut D by hand until the spindle lock prevents

further rotation and loosen collet nut D with wrench E

- insert an accessory in collet C as far as possible to

minimize run-out and unbalance

- push spindle-lock button B and hold it while you

tighten collet nut D with wrench E

! avoid excessive tightening of collet nut D

! never tighten collet nut, if there is no accessory

in collet; collet may be damaged

• Changing collets 6

! switch off the tool and disconnect the plug

- push spindle-lock button B and hold it while you

remove collet nut D

- remove collet C

- insert new collet

! never tighten collet nut, if there is no accessory

in collet; collet may be damaged

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o switch 7

- switch on/o the tool by pushing knob A in “I”/”O”

position

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

• Speed control 8

For optimal results on dierent materials

- select speed with wheel G (also while tool is running)

- use table 9 as reference for determining the right

speed

- before starting a job, nd the optimal speed by testing

out on spare material

! after longer periods of working at low speed,

allow the tool to cool down by running it for

approximately 3 minutes at high speed with

no load

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1415 AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 1415 AC Manual

Product: