701632
12
Zoom out
Zoom in
Previous page
1/164
Next page
12
c) Lower guard should be retracted manually only for
special cuts such as plunge cuts and compound
cuts. Raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released. For all other sawing, the lower guard
should operate automatically.
d) Always observe that the lower guard is covering the
blade before placing saw down on bench or floor.
An unprotected, coasting blade will cause the saw to
walk backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch is
released.
ADDITIONAL SAFETY WARNINGS
GENERAL
This tool should not be used by people under the age of
16 years
This tool is not suitable for wet cutting
Always disconnect plug from power source before
making any adjustment or changing any accessory
Never use the tool when cord is damaged; have it
replaced by a qualied person
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when connectable
Follow the dust-related national requirements for the
materials you want to work with
Only use a saw table provided with a switch that prevents
restarting of the motor after interruption of voltage
Only use a saw table provided with a kerf guide
ACCESSORIES
SKIL can assure awless functioning of the tool only
when original accessories are used
Use only saw blades that correspond with the characteristic
data given in these operation instructions and that are
tested and marked in accordance with EN 847-1
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
Use only saw blades with a minimum diameter of
184 mm, a maximum diameter of 190 mm and a
spindle hole of 16 mm
Never use saw blades made of high speed steel (HSS)
Never use grinding/cutting discs with this tool
BEFORE USE
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Remove all obstacles on top of as well as underneath the
cutting path before you start cutting
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
Use suitable detectors to find hidden utility lines or call
the local utility company for assistance (contact with
electric lines can lead to re or electrical shock; damaging a
gas line can result in an explosion; penetrating a water pipe
will cause property damage or an electrical shock)
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
The noise level when working can exceed 85 dB(A);
wear ear protection
Never use the tool without the original protection guard
system
Do not attempt to cut extremely small workpieces
Do not work overhead with the tool
In case of jamming or electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
When you put away the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
After switching o your circular saw, never stop the rotation
of the saw blade by a lateral force applied against it
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this
tool, it must be disposed of safely and not left unattended
USE
Mounting saw blade 2
! disconnect the plug
- take hex key A from storage B
- push spindle-lock button C and hold it while you
remove blade bolt D with hex key
! push spindle-lock button C only when tool is at a
standstill
- release spindle-lock button C
- remove ange E
- open lower guard F with lever G and hold it while you
mount saw blade with saw teeth and arrow printed on
saw blade pointing in same direction as arrow on
upper guard
- release lower guard F
- mount ange E
! make sure that clamping surfaces H of flanges
are perfectly clean and face the blade
- push spindle-lock button C and hold it while you
tighten blade bolt with hex key 1/8 turn past nger tight
(ensures slippage of saw blade when it encounters
excessive resistance thus reducing motor overload
and saw kickback)
- release spindle-lock button C
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 1054 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1054 in the language / languages: All languages as an attachment in your email.

The manual is 7,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info