480084
8
Zoom out
Zoom in
Previous page
1/96
Next page
8
MAINTENANCE / SERVICE
This tool is not intended for professional use
Before maintenance always switch off tool, ensure
there is no water pressure in tool and hand gun,
disconnect plug from power source, and disconnect
tool from water supply
Always keep tool and cord clean (especially ventilation
slots S 2)
- do not use water, solvents or polishes
- regularly clean spraying nozzle G using cleaning
needle M 0 (remove spray lance K from hand gun L
rst)
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
Cleaning water lter
- remove water lter E 2 from inlet connector C 2 with
long nose pliers
- rinse it clean and put it back (replace it when
damaged)
! never use the tool with a damaged water filter
Storage !
- store the tool out of reach of children in a location
where the ambient temperature will not exceed 40°C
or drop below 0°C
- do not place other objects on top of the tool
- securely mount storage rail N on the wall with 4
screws (not supplied) and horizontally leveled
- use storage rail N and storage straps P as illustrated
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switch off the tool and disconnect the plug before
investigating the problem
Spray is not consistent
- nozzle partly blocked -> clean nozzle
Motor does not start or stops suddenly
- power supply socket faulty -> use another socket
- plug not connected -> connect plug
- thermal protection switched o the motor -> let the tool
cool down for 5 minutes
Motor is running but spray is poor
- nozzle completely blocked -> clean nozzle
- water lter clogged -> clean water lter
- air in the pump -> ensure that water inlet connector is
securely tted
- inadequate water supply -> check that water tap is
fully open
ENVIRONMENT
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @ will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60335, EN 61000,
EN 55014 in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC,
2000/14/EC, 2011/65/EU
Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
ÊÆÇιÆ¼½ÊÄÇÇÌ
Á»½ʽËÁ¼½ÆÌ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
¹ÆÊÇÅŽĽÆ
ÈÈÊÇιÄ¹Æ¹¿½Ê
13.10.2011
11
NOISE/VIBRATION
Measured in accordance with EN 60704-1 the sound
pressure level of this tool is 81 dB(A) and the sound
power level 93 dB(A) (standard deviation: 2.2 dB), and
the vibration < 2.5 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
Measured in accordance with 2000/14/EC
(EN/ISO/5349) the guaranteed sound power level LWA is
lower than 97 dB(A)
The vibration emission level has been measured in
accordance with a standardised test given in
EN/ISO/5349; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
- using the tool for dierent applications, or with
dierent or poorly maintainted accessories, may
signicantly increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0760 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info