701723
13
Zoom out
Zoom in
Previous page
1/112
Next page
13
Inspect the extension cord periodically and replace it, if
damaged (inadequate extension cords can be
dangerous)
Never use the tool when cord is damaged; have it replaced
by a qualied person
Never operate the tool with a damaged cutting guard or
without the cutting guard mounted
Check the functioning of the tool before each use and after
any impact; in case of a defect, have it repaired immediately
by a qualied person (never open the tool yourself)
Before use, thoroughly inspect the cutting area and remove
any object that the tool may sling during cutting (such as
stones, loose pieces of wood, etc.)
DURING USE
Avoid using the tool in bad weather conditions, especially
when there is a risk of lightning
Do not use the tool on wet lawns
Keep proper balance and footing at all times; do not
overreach
Keep proper footing on slopes and do not mow extremely
steep slopes
Operate the tool at a walking pace only (do not run)
The cutting lines continue to rotate for a short time
after the tool is switched off
Do not cut grass which is not on the ground (e.g. on walls or
rocks)
Do not cross roads or gravel paths with the tool still running
Do not get distracted and always concentrate on what you
are doing
Always switch o tool, disconnect plug from power source,
and ensure that all moving parts have come to a complete
standstill
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
- after striking a foreign object
- whenever the tool starts vibrating abnormally
Always ensure that the ventilation openings are kept clear of
debris
EXPLANATION OF SYMBOLS ON TOOL
3 Warning! Read the instruction manual
4 Do not expose tool to rain
5 Wear protective glasses and hearing protection
6 Pay attention to the risk of injury caused by flying
debris (keep bystanders a safe distance away from work
area)
7 Immediately disconnect the plug if the (extension) cord is
damaged or cut through while working
8 Double insulation (no earth wire required)
9 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
If for any reason the old plug is cut o the cord of this tool, it
must be disposed of safely and not left unattended
Do not connect the blue (= neutral) or brown (= live) wire in
the cord of this tool to the earth terminal of the plug
USE
Assembly instructions 0
- the sequence of the numbers appearing in the drawing
corresponds with the sequence of the steps to be
followed for assembling the tool
- guide handle A 2 can be adjusted by loosening/
tightening knob B 2
! never use the tool without cutting guard C 2
! firmly tighten all screws, bolts and nuts
Cord restraint !
- hook the loop in the extension cord over restraint D as
illustrated
- pull tight to secure the extension cord
Height adjustment @
For adjusting the tool height so that your front arm is
straight when trimming
- unlock tube E by pushing button F
- extend tube E to the desired height (3 positions)
On/o #
- switch on tool by pressing trigger switch G
- switch o tool by releasing trigger switch G
! after switching off the tool the cutting lines
continue to rotate for a few seconds
- allow the cutting lines to stop rotating before switching
on again
! do not rapidly switch on and off
Trimming
! ensure that the cutting area is free of stones,
debris and other foreign objects
! start trimming only when tool runs at full speed
- start trimming near the mains socket and move away
while working
- cut long grass in layers (always start from the top)
- only trim with the tip of the cutting line
- do not cut damp or wet grass
- prevent the cut grass from clogging the spool (do not
make heavy cuts)
- do not overload the tool
- carefully cut around trees and bushes, so that they do
not come into contact with the cutting lines
- use ower guard H $ to protect vulnerable owers
- keep the tool away from solid objects in order to
protect the cutting lines against excessive wear
- be aware of the kickback forces that occur when solid
objects are touched
Holding and guiding the tool %
- for cutting long grass slowly swing the tool from right to
left and vice versa
- for cutting shorter grass tilt the tool as illustrated
- for trimming edges turn the cutting head 180° as
illustrated (possible only when lower tube E is
fixed in one of the three height positions)
- hold tool rmly with both hands, so you will have full
control of the tool at all times
- maintain a stable working position
- always hold the tool well away from your body
Line feeding ^
- two cutting lines will be released and cut o to the
correct length by line cutting blade J each time the tool
is switched on
! take care against injury from line cutting blade J
- after line feeding always return the tool to its normal
operating position before switching on
- feed the lines regularly to maintain full cutting circle
- when the motor runs without load and no grass is cut,
the cutting lines are worn or broken; rewind the spool
or replace the spool system
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0731 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0731 in the language / languages: All languages as an attachment in your email.

The manual is 10,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info