Manual Skil 0730 (page 7 of 112) (All languages)

591166

Zoom out

Zoom in

1/112

- after striking a foreign object

- whenever the tool starts vibrating abnormally

• Always ensure that the ventilation openings are kept clear

of debris

AFTER USE

• Alwaysswitchofftoolanddisconnectplugfrom

powersourcebeforemakingadjustments,changing

spools,cleaningorleavingthetoolunattendedfor

anyperiod

• Store the tool indoors in a dry and locked-up place, out

of reach of children

EXPLANATIONOFSYMBOLSONTOOL

3Warning! Read the instruction manual

4 Do not expose tool to rain

5 Wear protective glasses

6 Payattentiontotheriskofinjurycausedbyflying

debris (keep bystanders a safe distance away from work

area)

7 Immediately disconnect the plug if the (extension) cord is

damaged or cut through while working

8 Double insulation (no earth wire required)

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

USE

• Cutting guard 0

- mount cutting guard A as illustrated with round head

screw supplied

! neverusethetoolwithoutcuttingguardA

• Mounting/adjusting guide handle !

- mount guide handle B as illustrated with 4 screws

supplied

! firmlytightenall4screws

• Cord restraint @

- hook the loop in the extension cord over restraint C as

illustrated

- pull tight to secure the extension cord

• Height adjustment #

For adjusting the tool height so that your front arm is

straight when trimming

- loosen locking sleeve D 2 by turning it clockwise

- extend tube E 2 to the desired height

- tighten locking sleeve D 2 by turning it counter-

clockwise

• On/o $

- switch on tool by pressing trigger switch F

- switch o tool by releasing trigger switch F

! afterswitchingoffthetoolthecuttinglines

continuetorotateforafewseconds

- allow the cutting lines to stop rotating before switching

on again

! donotrapidlyswitchonandoff

• Trimming

! ensurethattheredcoverG2isremovedfrom

thelinecuttingbladebeforeusingthetool

! ensurethatthecuttingareaisfreeofstones,

debrisandotherforeignobjects

! starttrimmingonlywhentoolrunsatfullspeed

- start trimming near the mains socket and move away

while working

- cut long grass in layers (always start from the top)

- only trim with the tip of the cutting line

- do not cut damp or wet grass

- prevent the cut grass from clogging the spool (do not

make heavy cuts)

- do not overload the tool

- carefully cut around trees and bushes, so that they do

not come into contact with the cutting lines

- keep the tool away from solid objects in order to

protect the cutting lines against excessive wear

- be aware of the kickback forces that occur when solid

objects are touched

• Holding and guiding the tool %

- for cutting long grass slowly swing the tool from right to

left and vice versa

- for cutting shorter grass tilt the tool as illustrated

- turn the tool 180° for trimming edges

- hold tool rmly with both hands, so you will have full

control of the tool at all times

- maintain a stable working position

- always hold the tool well away from your body

• Line feeding ^

- tap button H lightly on the ground (preferably on a

solid surface) while the motor is running

- two cutting lines will be released and cut o to the

correct length by line cutting blade J

! ensurethattheredcoverG2isremovedfrom

thelinecuttingbladebeforeusingthetool

! takecareagainstinjuryfromlinecuttingbladeJ

- after line feeding always return the tool to its normal

operating position before switching on

- feed the lines regularly to maintain full cutting circle

- when the motor runs without load and no grass is cut,

the cutting lines are worn or broken; rewind the spool

or replace the spool system

• Rewinding spool &

In case the cutting lines fail to protrude from spool cap K

! switchoffthetoolanddisconnecttheplug

- remove spool system from tool and take out spool from

spool cap K

- tightly rewind both cutting lines evenly in layers in

arrow direction

- insert both lines into spool slots X and ensure that they

are securely in place (leave sucient length of line)

- thread both lines through spool holes Y before placing

the rewound spool into spool cap K

! ensurethatthespoolislocatedsecurelyinplace,

thenreleasebothlinesfromslotsXbypulling

themfirmly

- mount spool system onto tool (turnspoolclockwise

untilitclicksintoplace) *

• Replacing spool system *

! switchoffthetoolanddisconnecttheplug

- simply remove/mount old/new spool system as

illustrated

- only use SKIL spool system 2610Z01354 with this tool

(damageduetousingotherspoolsystemswillbe

excludedfromthewarranty)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0730 in the language / languages: All languages as an attachment in your email.

The manual is 9,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 0730 Manual

Product: