591144

Skil 0721 Manual

5
Zoom out
Zoom in
Previous page
1/44
Next page
5

Hand mower 0721
INTRODUCTION
• This product is intended for domestic lawn mowing only
! do not use the hand mower to cut grass on roofs
or balconies
• Check whether the packaging contains all parts as
illustrated in drawing 2
• When parts are missing or damaged, please contact your
dealer
TECHNICAL SPECIFICATIONS 1
TOOL ELEMENTS 2
A Push bar
B Wing nut for adjusting mowing height
C Bottom blade
D Screw for adjusting bottom blade
E Cutting blades
SAFETY
• Readthisinstructionmanualcarefullybeforeuse
and save it for future reference 3
• Take care when transporting the mower to the lawn, as
the cutting blades are sharp
• Always wear long trousers when mowing
• Do not operate the mower when barefoot or wearing
open sandals
• Thoroughly inspect the area where the mower is to be
used and remove all hard objects which could be caught
up and thrown by the cutting mechanism
• Always ensure that the cutting mechanism is in good
working order (have worn or damaged parts replaced)
• Keep all nuts, bolts and screws tight to be sure that the
mower is in safe working condition
• Only mow with sucient daylight or with appropriate
articial lighting
• Never mow in the direct vicinity of persons (especially
children) and animals
• Alwayskeephandsandfeetawayfromrotating
parts
• Operate the mower at a walking pace only (do not run)
• Keep proper footing on slopes and do not mow extremely
steep slopes
• Be extremely careful when moving backwards or pulling
the mower towards you
• Never leave the mower unattended
• Never let children or other persons who are not familiar
with the operating instructions use the product
USE
• Assembly instructions 4
- the sequence of the numbers appearing in the drawing
corresponds with the sequence of the steps to be
followed for assembling the hand mower
! firmlytightenallscrewsandnuts
• Adjusting cutting height (12-44 mm) 5
! wearprotectivegloves
- place the mower on a rm, at surface
- loosen both wing nuts B
- lift the housing in the center to the required cutting
height
- adjust the cutting height so that bottom blade C has no
ground contact if there are uneven areas on the lawn
surface
- tighten both wing nuts B
! ensure that wing nuts B are adjusted at the same
height on both sides
• Operating instructions
- hold the mower with both hands
- place the mower on the edge of the lawn and mow in a
forward direction
- reverse at the end of each turn, slightly overlapping the
previous cut strip
- only use the mower on dry grass
- keep the mower away from solid objects and plants
- for mowing long grass, rst set the cutting mechanism
to the maximum cutting height, then to a lower cutting
height
- adjust bottom blade C when the grass is not cut
cleanly and evenly
• Adjusting bottom blade 6
! prevententrapmentofthefingersbetween
movingcuttingbladesandfixedpartsofthe
mower
! wearprotectivegloves
- turn the mower upside down
- adjust bottom blade C to the required position by
loosening/tightening both adjustment screws D
- the adjustment is correct, if a piece of paper inserted
between cutting blades E and bottom blade C is cut
sharp like through a pair of scissors (to do this
carefully rotate the blade cylinder by hand)
MAINTENANCE / SERVICE
• Clean the mower after each use with a hand brush and a
soft cloth
! donotusewater(especiallynohigh-pressure
sprays)
- remove compacted grass cuttings from the blade area
with a wooden or plastic implement
• Lubricate the cutting blades regularly to avoid oxydation
• Regularly check for loose or damaged cutting blades,
and worn or damaged components
• The mower is equipped with self-sharpening cutting
blades
! beawarethattheself-sharpeningfunctiondoes
notwork,whenbottombladeCisnotcorrectly
adjusted (see 6)
• When necessary, take the mower to your dealer to have
the cutting mechanism sharpened
• Store the mower indoors in a dry place
• Do not place other objects on top of the mower when
stored
• If the appliance should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0721 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0721 in the language / languages: All languages as an attachment in your email.

The manual is 5,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info