Manual Skil 0711 (page 9 of 204) (All languages)

699801

Zoom out

Zoom in

1/204

• Alwayskeephandsandfeetawayfromrotating

parts

• Keepawayfromthedischargeopeningatalltimes

• Do not transport the tool while the motor is running

• Always switch o tool, disconnect plug from power

source, and ensure that all moving parts have come to a

complete standstill

- whenever leaving the tool unattended

- before clearing jammed material

- before checking, cleaning or working on the tool

- after striking a foreign object

- whenever the tool starts vibrating abnormally

• If the cutting mechanism strikes any foreign object or if

the tool should start making any unusual noise or

vibration, immediately switch o, allow the cutting blade

to stop, disconnect the plug and take the following steps

- inspect for damage

- replace or repair any damaged parts

- check for and tighten any loose parts

AFTER USE

• Thecuttingbladecontinuestorotateforashort

timeaftertoolisswitchedoff(donottouchrotating

blade)

• Store the tool indoors in a dry and locked-up place, out

of reach of children

EXPLANATION OF SYMBOLS ON TOOL

4 Read the instruction manual before use

5 Double insulation (no earth wire required)

6 Wear protective glasses and hearing protection

7 Payattentiontotheriskofinjurycausedbyflying

debris (keep bystanders a safe distance away from work

area)

8 Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (donottouchthecord

beforedisconnectingtheplug)

9 Do not dispose of the tool together with household waste

material

USE

• Assembly instructions 2

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the lawn mower

! firmlytightenallscrews

- fasten screws A so that handle B moves freely

• Cord restraint 0

- hook the loop in the extension cord over restraint C as

illustrated

- pull tight to secure the extension cord

• Adjusting guide handle !

Handle B can be adjusted into the following three

positions

- ‘D’ (drive position) -> for mowing at exible working

height

- ‘P’ (park position) -> when emptying the grass box or

during work breaks

- ‘S’ (storage position) -> when storing the tool

• Adjusting cutting height (25-40-55 mm) @

! disconnectplugfrompowersourceandensure

thatthecuttingbladehasstoppedrotating

- put handle B 3 in storage position ‘S’

- turn the mower upside down

- locate the two front wheels as well as the two rear

wheels into the desired cutting height position (25, 40

or 55 mm)

- after adjusting cutting height, always check if grass

box E 3 is still securely in place

• On/o safety switch #

Prevents the tool from being switched on accidentally

- switch on tool by rst pressing safety switch F and

then pulling trigger switch G

- switch o tool by releasing trigger switch G

! afterswitchingoffthetoolthebladecontinuesto

rotateforafewseconds

• Operating instructions

- hold the mower with both hands

- place the mower on the edge of the lawn and mow in a

forward direction

- reverse at the end of each turn, slightly overlapping the

previous cut strip

- keep the mower away from solid objects and plants

! onlyusethemowerondrygrass

! formowinglonggrass,firstsetthecutting

mechanismtothemaximumcuttingheight,then

toalowercuttingheight

! adjustyourwalkingpacewhenmowinglong

grass

• Storage $

- for saving substantial storage space put handle B 3 in

storage position ‘S’ and store the tool as illustrated;

emptygrassboxfirst

- do not place other objects on top of the mower when

stored

- store the mower indoors in a dry place

- always allow the tool to cool down before storing

• Replacing cutting blade %

- disconnect plug from power source

- simply remove/mount old/new cutting blade as

illustrated

- after replacing the cutting blade test-run the tool for at

least one minute without load to ensure that the tool is

operating properly

! onlyusereplacementcuttingbladesofthe

correcttype(SKILaccessory2610Z04031/BOSCH

accessoryF016800183)

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Keep all nuts, bolts and screws tight to be sure that the

tool is in a safe working condition

• Regularly check the grass box for wear or damage

• Alwaysdisconnectplugfrompowersourcebefore

cleaningand/ormaintenance

• Beawarethatduringcleaning/maintenance(even

thoughthetoolisswitchedoff)thecuttingblade

canstillbemoved

• Always keep tool and cord clean (especially ventilation

slots H 3)

• Clean the mower after each use with a hand brush and a

soft cloth

- remove compacted grass cuttings from the blade area

with a wooden or plastic implement

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0711 in the language / languages: All languages as an attachment in your email.

The manual is 20,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 0711 Manual

Product: