757185
13
Zoom out
Zoom in
Previous page
1/132
Next page
13
-clean line cutting blade N 2 and cutting guard A 2
after each use
-clean ventilation slots W 2 regularly with a brush or
compressed air
Regularly check the condition of the cutting head and the
tightness of nuts, bolts and screws
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
Storage
Storage method 1 s
-securely mount storage rail Q on the wall with 2 screws
(not supplied) and horizontally leveled
-attach the storage adapter R and move it against the
mounting base of the storage rail Q
-store the tool with the storage hole in the handle over
the tip of the storage adapter
Storage method 2 u
-use pivot position 1 and let the tool stand by itself on
the ground
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the SKIL warranty conditions see
www.skil.com or ask your dealer)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! in case of electrical or mechanical malfunction,

Tool does not operate
-empty battery -> charge battery
-hot battery -> let battery cool down
-internal fault -> contact dealer/service station
Tool operates intermittently
-internal wiring defective -> contact dealer/service
station
-      
Tool vibrates abnormally
-grass too high -> cut in stages
Tool does not cut
-        
Line cannot be fed
-spool empty -> replace spool
-line entangled inside spool -> inspect spool; rewind if
necessary
           
cutting blade
Line keeps breaking
-line entangled inside spool -> inspect spool; rewind if
necessary
-trimmer incorrectly used -> only trim with the tip of the
line; avoid stones, walls and other hard objects; feed
the line regularly
-keep the tool away from solid objects in order to protect
the cutting line against excessive wear
-be aware of the kickback forces that occur when solid
objects are touched
Holding and guiding the tool o p
-for cutting long grass slowly swing the tool from right to
left and vice versa
-for cutting shorter grass tilt the tool as illustrated
-          
control of the tool at all times
-maintain a stable working position
-always hold the tool well away from your body
-for edging let the tool be supported by the edging
wheel S p
Line feeding
The line is automatically fed when the tool is switched
  
-           
length by line cutting blade N
! take care against injury from line cutting blade N
    a
-       
-pull the line and keep pulling, then press and release
the line feed button T
-after line feeding always return the tool to its normal
operating position before switching on
-feed the line regularly to maintain full cutting circle
-when the motor runs without load and no grass is cut,
the cutting line is stuck, worn or broken; rewind the
spool or replace the spool system
Rewinding spool d
In case the cutting line fails to protrude from spool hole L
! 
-remove spool cover J and take out spool K from spool
holder V
-tightly rewind the cutting line evenly in layers in arrow
direction
-insert the cutting line into spool slot Z and ensure that it
        
-thread the cutting line through spool hole L before
placing the rewound spool into spool holder V
! ensure that the spool is located securely in place,
then pull the cutting line from slot Z
-mount spool cover J
Replacing spool d
! 
-remove old spool and mount new spool as illustrated
-only use SKIL spool 2610S00818 with this tool
(damage due to using other spools will be
excluded from the warranty)
-after replacing the spool test-run the tool for at least
one minute without load to ensure that the tool is
operating properly
! 
battery
MAINTENANCE / SERVICE
This tool is not intended for professional use
        
ensure that all moving parts have come to a complete
standstill
Always keep tool clean (especially ventilation slots W 2)
-clean the tool with a damp cloth (do not use cleaning
agents or solvents)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0240 in the language / languages: All languages as an attachment in your email.

The manual is 4,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info