527736
63
Zoom out
Zoom in
Previous page
1/72
Next page
Wi-Fi router X8 AC1750
WLR-8100
User Manual
Table of Contents
Introduction ............................................................................................................ 3
Key Features ............................................................................................................ 4
Package Contents ..................................................................................................... 5
Cautions ................................................................................................................ 6
Product Layout......................................................................................................... 7
Network + System Requirements .................................................................................... 9
Setup your Router ....................................................................................................10
Setup your Computer ................................................................................................11
Login to your Router .................................................................................................14
Configure your Internet connection ...............................................................................15
Configure your Router ...............................................................................................18
Wireless Settings ......................................................................................................22
Firewall Settings ......................................................................................................30
Advanced Settings ...................................................................................................34
Toolbox Settings ......................................................................................................41
Addendum A: USB Port Control Center ............................................................................49
Addendum B: GNU/GPL Leaflet .....................................................................................60
Addendum C: GNU/GPL .............................................................................................62
Addendum D: Declaration of Conformity .........................................................................71
Revision 1.0
© Sitecom Europe BV 2013
Note: All the information contained in this manual was correct at the time of publication.
However, as our engineers are always updating and improving the product, your device‟s
software may have a slightly different appearance or modified functionality than presented in
this manual.
Introduction
Congratulations on your purchase of the WiFi Router X8 AC1750. This router is compliant with
802.11a/b/g/n/ac and up to 6 times faster than standard 802.11n based routers while still being
compatible with 802.11g & 802.11b devices. This router is not only a Wireless Access Point, but
also doubles as a 4-port full-duplex Gigabit switch that connects your wired-Ethernet devices
together at 10/100/1000 Mbps speeds.
At 450Mbps wireless transmission rate on 2.4GHz and 1300 Mbps wireless transmission rate on
5GHz, the Access Point built into the router uses advanced MIMO (Multi-Input, Multi-Output)
technology to transmit multiple streams of data in a single wireless channel, giving you
seamless access to multimedia content. The robust RF signal travels farther, eliminates dead
spots and extends the network range. For data protection and privacy, the router encodes all
wireless transmissions with WEP, WPA, or WPA2 encryption.
With the built-in DHCP Server & powerful SPI firewall, the router protects your computers
against intruders and most known Internet attacks and also provides safe VPN pass-through.
With the incredible speed and QoS function of 802.11n, the router is ideal for media-centric
applications like streaming video, gaming, and VoIP telephony to run multiple media-intense
data streams through the network at the same time, with no degradation in performance.
With Sitecom Cloud Security, Sitecom goes one step further and ensures that you can surf the
Internet even more safely, not only on your PC, but on all the devices in your home which you
use to access the Internet. It does not matter whether you surf the Internet on a laptop, a tablet,
a mobile telephone or your television. Thanks to the security that is integrated in the router, all
the Internet devices in your home are protected against the dangers of Internet criminality.
Key Features
Features
Advantages
Incredible Data Rate up to 1300Mbps*
Heavy data payloads such as MPEG video
streaming
IEEE 802.11n Compliant and backwards
compatible with 802.11b/g/n
Fully Interoperable with IEEE 802.11b /
IEEE802.11g, IEEE 802.11n compliant
devices with legacy protection
Four 10/100/1000 Mbps gigabit Switch
Ports (Auto-Crossover)
Scalability, extend your network.
Firewall supports Virtual Server
Mapping, DMZ, IP Filter, ICMP Blocking,
SPI
Avoids the attacks of Hackers or Viruses
from Internet
Support 802.1x authenticator, 802.11i
(WPA/WPA2, AES), VPN pass-through
Provide mutual authentication (Client and
dynamic encryption keys to enhance
security
Sitecom Cloud Security
Protect your home against cybercrime
while browsing.
USB Port
Connect any USB device and share it in your
network.
Guest Network
Devices connected to the Guest network
will have Internet connection but no access
to the main network and cannot
communicate with each other.
IPv6 support
Support for Static, Native, 6RD and DS-Lite.
* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n, ac chipset used.
Actual throughput may vary. Network conditions and environmental factors lower actual
throughput rate. All specifications are subject to change without notice.
Package Contents
Open the package carefully, and make sure that none of the items listed below are missing. Do
not discard the packing materials, in case of return; the unit must be shipped back in its original
package.
The WLR-8100 WiFi Router X8 AC1750
A 110V~240V to 12V 2A Switching Power Adapter
A Quick Install Guide
A CD-ROM with software
An UTP cable
Cautions
This router‟s design and manufacturer has your safety in mind. In order to safely and effectively
use this router, please read the following before usage.
Usage Cautions
The user should not modify this router. The environmental temperature should be within +5 ~
+35 degrees Celsius.
Power
The router‟s power voltage is DC 12V 2A.
When using this router, please connect the supplied AC adapter or AC adapter cable to the
router‟s power jack. When placing the adapter cable, make sure it can‟t get damaged or be
subject to pressure. To reduce the risk of electric shock, unplug the adapter first before cleaning
it. Never connect the adapter to the router in a humid or dusty area. Do not replace the adapter
or cable‟s wire or connector.
Repair
If the router has a problem, you should take it to an appointed repair center and let the
specialists do the repair. Never repair the router yourself, you might damage the router or
endanger yourself.
Disposing of the Router
When you dispose of the router, be sure to dispose it appropriately. Some countries may
regulate disposal of an electrical device, please consult with your local authority.
Others
When using this router, please do not let it come into contact with water or other liquids. If
water is accidentally spilled on the router, please use a dry cloth to absorb the spillage.
Electronic products are vulnerable, when using please avoid shaking or hitting the router, and
do not press the buttons too hard.
Do not let the router come into contact with water or other liquid.
Do not disassemble, repair or change the design of the router; any damage done will
not be included in the repair policy.
Avoid hitting the router with a hard object, avoid shaking the router and stay away from
magnetic fields.
If during electrostatic discharge or a strong electromagnetic field the product will
malfunction, unplug the power cable. The product will return to normal performance
the next time it is powered on.
Product Layout
Port
Description
Power connector
Connect the 12V DC adapter to this port
LAN (Yellow)
Connect your PCs or network devices to these ports
WAN (Blue)
Connect your ADSL/Cable modem to this port
USB Port
Connect a USB device to this port
Backlabel and Network Details Folder
The Network Details Folder describes the IP address, login details, network name, security code
and OPS button functionality.
Button
Description
OPS BUTTON
Press 2 seconds for WPS/OPS mode
Press both buttons 15+ Seconds to reset to factory defaults.
LED Definition
As shown from the top to the bottom.
Port
Description
OPS (White)
Shows OPS activity.
Power (Red)
Shows the device is turned on.
5GHz WiFi (Blue)
Shows 5GHz WiFi activity.
2.4GHz WiFi (Blue)
Shows 2.4GHz WiFi activity.
WAN (Blue)
Shows the WAN cable is connected.
LAN (Blue)
Shows the cable is connected.
LAN (Blue)
Shows the cable is connected.
LAN (Blue)
Shows the cable is connected.
LAN (Blue)
Shows the cable is connected.
Network + System Requirements
To begin using the router, make sure you meet the following as minimum requirements:
PC/Notebook.
Operating System Microsoft Windows XP/VISTA/7 or Mac OSX
1 Free Ethernet port.
WiFi card/USB dongle (802.11 a/b/g/n) optional.
External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera)
Ethernet compatible CAT5e cables.
Setup your Router
You can place the router on a desk or other flat surface, or you can mount it on a wall. For
optimal performance, place your router in the center of your home (or your office) in a location
that is away from any potential source of interference, such as a metal wall or microwave oven.
This location must be close to a power connection and your ADSL/Cable modem.
Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet.
Switch the router on by flipping the switch on the back of the device. The router automatically
enters the self-test phase. During self-test phase, the Power LED will be lit continuously to
indicate that this product is in normal operation.
Setup your Computer
Windows, Manual Connection
Click on the icon for wireless connectivity. This is usually located in the System Tray, next
to the clock.
Select the Sitecom network. The correct network name can be found on the sticker on
bottom of the router, or in the Network Details Folder.
Fill in the password for the wireless network. The correct password can be found on the
sticker on the bottom of the router, or in the Network Details Folder.
Wait for the icon to display that it‟s connected to the network.
Windows, OPS Connection
Click on the icon for wireless connectivity. This is usually located in the System Tray, next
to the clock.
Select the Sitecom network. The correct network name can be found on the sticker on
bottom of the router, or in the Network Details Folder.
Push the OPS Button on the router. For 2.4GHz, press 0-5 seconds. For 5GHz, press 5-10
seconds.
Wait for the icon to display that it‟s connected to the network.
Mac OSX
Click on the icon for wireless connectivity. This is usually located in the System Tray, next
to the clock.
Select the Sitecom network. The correct network name can be found on the sticker on
bottom of the router, or in the Network Details Folder.
Fill in the password for the wireless network. The correct password can be found on the
sticker on the bottom of the router, or in the Network Details Folder.
Wait for the icon to display that it‟s connected to the network.
Login to your Router
LOGIN procedure
OPEN your browser (e.g. Internet Explorer).
Type http://sitecom.router in the address bar and press [Enter].
Type user name and password. The default username is admin, the password can be
found on the back label on the bottom of your router.
Click OK.
You will see the home page of the WiFi Router X8 AC1750.
Configure your Internet connection
From the menu, select “Internet Settings”.
Depending on the chosen setting, you may need to enter your user name and password, MAC
address or hostname in the following window. After you have entered the correct information,
click Apply.
IPv6 Configuration
The IPv6 (Internet Protocol version 6) section is where you configure your IPv6 Connection type.
IPv6 Connection Type
There are several connection types to choose from: Static IPv6, Autoconfiguration, 6RD and
Link-local only. If you are unsure of your connection method, please contact your IPv6 Internet
Service Provider.
Static IPv6 Mode
This mode is used when your ISP provides you with a set IPv6 addresses that does not change.
The IPv6 information is manually entered in your IPv6 configuration settings. You must enter
the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server and Secondary
DNS Server. Your ISP provides you with all this information.
6RD Mode
In the 6RD mode, no additional configuration is necessary.
Link-local Mode
The Link-local address is used by nodes and routers when communicating with neighboring
nodes on the same link. This mode enables IPv6-capable devices to communicate with each
other on the LAN side.
Configure your Router
Status
The System status section allows you to monitor the current status of your router, the UP time,
hardware information and serial number as well as firmware version information is displayed
here.
DHCP Server
The DHCP Server tab gives you the opportunity to change the IP settings of the router.
Click Apply at the bottom of this screen to save any changes.
IP address 192.168.0.1: It is the router‟s LAN IP address (Your LAN clients default
gateway IP address).
IP Subnet Mask 255.255.255.0: Specify a Subnet Mask for your LAN segment.
802.1d Spanning Tree: Disabled by default. If the 802.1d Spanning Tree function is
enabled, this router will use the spanning tree protocol to prevent network loops.
DHCP Server: Enabled by default. You can enable or disable the DHCP server. When
DHCP is disabled no ip-addresses are assigned to clients and you have to use static
ip-addresses. When DHCP server is enabled your computers will be assigned an ip-
address automatically until the lease time expires.
Lease Time: One Week. In the Lease Time setting you can specify the time period
that the DHCP lends an IP address to your LAN clients. The DHCP will change your
LAN client‟s IP address when this time threshold period is reached.
IP Address Pool: You can select a particular IP address range for your DHCP server to
issue IP addresses to your LAN Clients. The default IP range is 192.168.0.100 ~
192.168.0.200. If you want your PC(s) to have a static/fixed IP address, then you‟ll
have to choose an IP address outside this IP address Pool
Domain Name: You can specify a Domain Name for your LAN or just keep the default
(sitecom.router).
Device Status
View the router‟s current configuration settings. Device Status displays the configuration
settings you‟ve configured in the Internet Settings and WiFi Settings sections.
Internet Status
This page displays whether the WAN port is connected to a Cable/DSL connection. It also
displays the router‟s WAN IP address, Subnet Mask, and ISP Gateway as well as MAC address, the
Primary DNS. Press Renew button to renew your WAN IP address.
DHCP Client Status
This page shows all DHCP clients (LAN PCs) currently connected to your network. The table
shows the assigned IP address, MAC address and expiration time for each DHCP leased client.
Use the Refresh button to update the available information.
You can check Enable Static DHCP IP. It is possible to add more static DHCP IPs. They are listed
in the table Current Static DHCP Table. IP can be deleted at will from the table.
Click Apply to save the changed configuration.
WLR-8100 Log
View the operation log of the router. This page shows the current system log of the router. It
displays any event that occurred during or after system start up. At the bottom of the page, the
system log can be saved <Save> to a local file for further processing or the system log can be
cleared <Clear> or it can be refreshed <Refresh> to get the most updated information. When
the system is powered down, the system log will disappear if not saved to a local file.
WLR-8100 Statistics
Shows the counters of packets sent and received on WAN, LAN & WLAN.
Wireless Settings
You can set parameters that are used for the wireless stations to connect to this router for the
2.4 GHz radio or 5 GHz radio. The parameters include Mode, ESSID, Channel Number and
Associated Client.
Wireless Function
Enable or Disable Wireless function here. Click Apply and wait for module to be ready & loaded.
Basic Settings
Band: Allows you to set the AP fixed at 802.11b or 802.11g mode. You can also select
B+G mode to allow 802.11b and 802.11g clients at the same time. For the 5GHz
mode you can set 802.11a, 802.11n, 802.11a/n or 802.11ac mode.
Guest Network: Enable this to activate the Guest Network. Devices connected to the
Guest network will have Internet connection but no access to the main network and
cannot communicate with each other
SSID: This is the name of the wireless signal which is broadcasted. All the devices in
the same wireless LAN should have the same SSID.
Channel: The channel used by the wireless LAN. All devices in the same wireless LAN
should use the same channel.
Guest Network
Guest IP address: The gateway address for the Guest Network. This address cannot
be the same as the default router‟s IP Address.
Guest Subnet Mask: The Subnet Mask for the Guest network. This address cannot be
the same as the default router‟s Subnet Mask.
Guest Lease Time: One Week. In the Lease Time setting you can specify the time
period that the DHCP lends an IP address to your LAN clients. The DHCP will change
your LAN client‟s IP address when this time threshold period is reached.
Guest Start IP + End IP: You can select a particular IP address range for your DHCP
server to issue IP addresses to your LAN Clients. The default IP range is
192.168.169.100 ~ 192.168.169.200. This address pool cannot be the same as the
default router‟s DHCP Address pool.
Guest SSID: This is the name of the wireless signal which is broadcasted as the Guest
Network. This name cannot be the same as the default SSID.
Advanced Settings
This tab allows you to set the advanced wireless options. The options included are, Fragment
Threshold, RTS Threshold, Beacon Interval, and Preamble Type. You should not change these
parameters unless you know what effect the changes will have on the router.
Fragment Threshold: "Fragment Threshold" specifies the maximum size of a packet
during the fragmentation of data to be transmitted. If you set this value too low, it
will result in bad performance.
RTS Threshold: When the packet size is smaller then the RTS threshold, the wireless
router will not use the RTS/CTS mechanism to send this packet.
Beacon Interval: This is the interval of time that this wireless router broadcasts a
beacon. A Beacon is used to synchronize the wireless network.
Data Rate: The “Data Rate” is the rate that this access point uses to transmit data
packets. The access point will use the highest possible selected transmission rate to
transmit the data packets.
N Data Rate: The “Data Rate” is the rate that this access point uses to transmit data
packets for N compliant wireless nodes. Highest to lowest data rate can be fixed.
Channel Bandwidth: This is the range of frequencies that will be used.
Preamble Type: The “Long Preamble” can provide better wireless LAN compatibility
while the “Short Preamble” can provide better wireless LAN performance.
TX Power: The transmit power can be set to a bare minimum or maximum power for
better performance or power saving.
Security
This router provides complete wireless LAN security functions, included are WEP, IEEE 802.11x,
IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security
functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless
stations use the same security function, and are setup with the same security key.
Disable
When you choose to disable encryption, it is very insecure to use the router.
Enable 802.1x Authentication
IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this
Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS
server. This mode only authenticates users by IEEE 802.1x, but it does not encrypt the data
during communication
WEP
When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can
generate the key by yourself and enter it. You can enter four WEP keys and select one of them
as a default key. Then the router can receive any packets encrypted by one of the four keys.
Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit. The
larger the key will be the higher level of security is used, but the throughput will be
lower.
Key Type: You may select ASCII Characters (alphanumeric format) or Hexadecimal
Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.
Key1 - Key4: The WEP keys are used to encrypt data transmitted in the wireless
network. Use the following rules to setup a WEP key on the device. 64-bit WEP: input
10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as
the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-
9" range) or 13-digit ASCII characters as the encryption keys.
Click Apply at the bottom of the screen to save the above configuration.
WPA Pre-shared Key
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a pre-shared key to
authenticate wireless stations and encrypt data during communication. It uses TKIP or CCMP
(AES) to change the encryption key frequently, so the encryption key is not easy to be cracked
by hackers. This is the best security available.
WPA-Radius
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS
server to authenticate wireless stations and provide the session key to encrypt data during
communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. Press
Apply when you are done.
ACL
This wireless router supports MAC Address Control, which prevents unauthorized clients from
accessing your wireless network.
Enable wireless access control: Enables the wireless access control function
Adding an address into the list: Enter the "MAC Address" and "Comment" of the
wireless station to be added and then click "Add". The wireless station will now be
added into the "Current Access Control List" below. If you are having any difficulties
filling in the fields, just click "Clear" and both "MAC Address" and "Comment" fields
will be cleared.
Remove an address from the list: If you want to remove a MAC address from the
"Current Access Control List ", select the MAC address that you want to remove in
the list and then click "Delete Selected". If you want to remove all the MAC addresses
from the list, just click the "Delete All" button. Click "Reset" will clear your current
selections.
Click Apply at the bottom of the screen to save the above configurations. You can now
configure other sections by choosing Continue, or choose Apply to apply the settings and
reboot the device.
WPS
Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection between the wireless
clients and the wireless router. You don‟t have to select the encryption mode and fill in a long
encryption passphrase every time when you try to setup a wireless connection. You only need
to press a button on both wireless client and wireless router, and WPS will do the rest for you.
The wireless router supports two types of WPS: WPS via Push Button and WPS via PIN code. If
you want to use the Push Button, you have to push a specific button on the wireless client or in
the utility of the wireless client to start the WPS mode, and switch the wireless router to WPS
mode. You can simply push the WPS button of the wireless router, or click the „Start to Process‟
button in the web configuration interface. If you want to use the PIN code, you have to know
the PIN code of the wireless client and switch it to WPS mode, then fill-in the PIN code of the
wireless client through the web configuration interface of the wireless router.
WPS: Check the box to enable WPS function and uncheck it to disable the WPS
function.
WPS Current Status: If the wireless security (encryption) function of this wireless
router is properly set, you‟ll see a „Configured‟ message here. Otherwise, you‟ll see
„UnConfigured‟.
Self-Pin Code: This is the WPS PIN code of the wireless router. You may need this
information when connecting to other WPS-enabled wireless devices.
SSID: This is the network broadcast name (SSID) of the router.
Authentication Mode: It shows the active authentication mode for the wireless
connection.
Passphrase Key: It shows the passphrase key that is randomly generated by the
wireless router during the WPS process. You may need this information when using
a device which doesn‟t support WPS.
WPS via Push Button: Press the button to start the WPS process. The router will wait
for the WPS request from the wireless devices within 2 minutes.
WPS via PIN: You can fill-in the PIN code of the wireless device and press the button
to start the WPS process. The router will wait for the WPS request from the wireless
device within 2 minutes.
Firewall Settings
The router provides extensive firewall protection by restricting connection parameters, thus
limiting the risk of hacker attacks, and defending against a wide array of common Internet
attacks. However, for applications that require unrestricted access to the Internet, you can
configure a specific client/server as a Demilitarized Zone (DMZ).
Note: To enable the Firewall settings select Enable and click Apply
DMZ
If you have a client PC that cannot run an Internet application (e.g. Games) properly from
behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way
Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets
going to your WAN port IP address to a particular IP address in your LAN. The difference
between the virtual server and the DMZ function is that the virtual server re-directs a particular
service/Internet application (e.g. FTP, websites) to a particular LAN client/server, whereas DMZ
re-directs all packets (regardless of services) going to your WAN IP address to a particular LAN
client/server.
Enable DMZ: Enable/disable DMZ
Public IP Address: The IP address of the WAN port or any other Public IP addresses given
to you by your ISP
Client PC IP Address: Fill-in the IP address of a particular host in your LAN that will
receive all the packets originally going to the WAN port/Public IP address above.
Click Apply at the bottom of the screen to save the above configurations.
Denial of Service (DoS)
The Broadband router's firewall can block common hacker attacks, including Denial of Service,
Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the events.
Ping of Death: Protection from Ping of Death attacks
Discard Ping From WAN: The router‟s WAN port will not respond to any Ping requests
Port Scan: Protects the router from Port Scans.
Sync Flood: Protects the router from Sync Flood attack.
Click Apply at the bottom of the screen to save the above configuration.
Access
You can restrict users from accessing certain Internet applications/services (e.g. Internet
websites, email, FTP etc.), Access Control allows users to define the traffic type permitted in your
LAN. You can control which PC client can have access to these services.
Deny: If you select “Deny” then all clients will be allowed to access Internet accept for
the clients in the list below.
Allow: If you select “Allow” then all clients will be denied to access Internet accept for
the PCs in the list below.
Filter client PCs by IP: Fill in “IP Filtering Table” to filter PC clients by IP.
Add PC: You can click Add PC to add an access control rule for users by IP addresses.
Remove PC: If you want to remove some PCs from the "IP Filtering Table", select the PC
you want to remove in the table and then click “Delete Selected". If you want to remove
all PCs from the table, just click the "Delete All" button.
Filter client PC by MAC: Check “Enable MAC Filtering” to enable MAC Filtering.
Add PC: Fill in “Client PC MAC Address” and “Comment” of the PC that is allowed to
access the Internet, and then click “Add”. If you find any typo before adding it and want
to retype again, just click "Reset" and the fields will be cleared.
Remove PC: If you want to remove some PC from the "MAC Filtering Table", select the
PC you want to remove in the table and then click "Delete Selected". If you want to
remove all PCs from the table, just click the "Delete All" button. If you want to clear the
selection and re-select again, just click “Reset”.
Click Apply at the bottom of the screen to save the above configuration.
URL block
You can block access to some Web sites from particular PCs by entering a full URL address or
just keywords of the Web site.
Enable: URL Blocking Enable/disable URL Blocking
Add URL/keyword: Fill in “URL/Keyword” and then click “Add”. You can enter the full URL
address or the keyword of the web site you want to block.
Remove URL/keyword: If you want to remove some URL keywords from the "Current
URL Blocking Table", select the URL keyword you want to remove in the table and then
click "Delete Selected". If you want remove all URL keywords from the table, just click
"Delete All" button. If you want to clear the selection and re-select again, just click
“Reset”.
Click Apply at the bottom of the screen to save the above configuration.
Advanced Settings
Network Address Translation (NAT) allows multiple users at your local site to access the Internet
through a single Public IP Address or multiple Public IP Addresses. NAT provides Firewall
protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses
to Public IP Addresses for key services such as Websites and FTP.
NAT: Select Disable to disable the NAT function.
Hardware Accelerator: Select Enable to use hardware acceleration for routing. This gives
a speed increase in WAN->LAN performance. Please note that this disables the QoS
service.
Port Forwarding
Port Forwarding allows you to re-direct a particular range of service port numbers (from the
Internet/WAN Port) to a particular LAN IP address. It helps you to host servers behind the router
NAT firewall.
Enable Port Forwarding: Enable Port Forwarding
Local IP: This is the private IP of the server behind the NAT firewall.
Type: This is the protocol type to be forwarded. You can choose to forward “TCP” or
“UDP” packets only, or select “both” to forward both “TCP” and “UDP” packets.
Port Range: The range of ports to be forward to the private IP.
Comment: description of this setting.
Add: Fill in the "Private IP", “Type”, “Port Range” and "Comment" of the setting to be
added and then click "Add". Then this Port Forwarding setting will be added into the
"Current Port Forwarding Table" below.
Remove: If you want to remove a Port Forwarding setting from the "Current Port
Forwarding Table", select the Port Forwarding setting that you want to remove in the
table and then click "Delete Selected". If you want to remove all Port Forwarding
settings from the table, just click "Delete All" button. Click "Reset" will clear your current
selections.
Click Apply at the bottom of the screen to save the above configuration.
Virtual Server
Use the Virtual Server function when you want different servers/clients in your LAN to handle
different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet.
Computers use numbers called port numbers to recognize a particular service/Internet
application type. The Virtual Server allows you to re-direct a particular service port number
(from the Internet/WAN Port) to a particular LAN private IP address and its service port number.
Enable Virtual Server: Enable Virtual Server.
Local IP: This is the LAN client/host IP address that the Public Port number packet will be
sent to.
Local Port: This is the port number (of the above Private IP host) that the below Public
Port number will be changed to when the packet enters your LAN (to the LAN
Server/Client IP).
Type: Select the port number protocol type (TCP, UDP or both). If you are unsure, then
leave it to the default “both” setting. Public Port Enter the service (service/Internet
application) port number from the Internet that will be re-directed to the above Private
IP address host in your LAN
Comment: The description of this setting.
Add: Fill in the "Private IP", "Private Port", "Type", “Public Port” and "Comment" of the
setting to be added and then click "Add". Then this Virtual Server setting will be added
into the "Current Virtual Server Table" below.
Reset: If you want to remove Virtual Server settings from the "Current Virtual Server
Table", select the Virtual Server settings you want to remove in the table and then click
"Delete Selected". If you want to remove all Virtual Server settings from the table, just
click the "Delete All" button. Click "Reset" will clear your current selections.
Click Apply at the bottom of the screen to save the above configuration.
Special Applications
Some applications require multiple connections, such as Internet games, video Conferencing,
Internet telephony and others. In this section you can configure the router to support multiple
connections for these types of applications.
Enable Trigger Port: Enable the Special Application function.
Trigger Port: This is the outgoing (Outbound) range of port numbers for this particular
application.
Trigger Type: Select whether the outbound port protocol is “TCP”, “UDP” or both.
Public Port: Enter the In-coming (Inbound) port or port range for this type of application
(e.g. 2300-2400, 47624).
Public Type: Select the Inbound port protocol type: “TCP”, “UDP” or both.
Comment: The description of this setting.
Popular applications: This section lists the more popular applications that require
multiple connections. Select an application from the Popular Applications selection.
Once you have selected an application, select a location (1-10) in the Copy to selection
box and then click the Copy to button. This will automatically list the Public Ports
required for this popular application in the location (1-10) you specified.
Add: Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type", "Public Port"
and "Comment" of the setting to be added and then click "Add". The Special Application
setting will be added into the "Current Trigger-Port Table" below. If you happen to make
a mistake, just click "Clear" and the fields will be cleared.
Reset: If you want to remove Special Application settings from the "Current Trigger-Port
Table", select the Special Application settings you want to remove in the table and then
click "Delete Selected". If you want remove all Special Application settings from the
table, just click the "Delete All" button. Click "Reset" will clear your current selections.
Click Apply at the bottom of the screen to save the above configuration.
UPnP
With UPnP, all PCs in you Intranet will discover this router automatically, so you don‟t have to
configure your PC and it can easily access the Internet through this router.
UPnP Feature: You can enable or Disable the UPnP feature here. After you enable the UPnP
feature, all client systems that support UPnP, like Windows XP, can discover this router
automatically and access the Internet through this router without having to configure anything.
The NAT Traversal function provided by UPnP can let applications that support UPnP connect to
the internet without having to configure the virtual server sections.
Click Apply at the bottom of the screen to save the above configuration.
QoS
QoS can let you classify Internet application traffic by source/destination IP address and port
number. You can assign priority for each type of application and reserve bandwidth for it. The
packets of applications with higher priority will always go first. Lower priority applications will
get bandwidth after higher priority applications get enough bandwidth. This can let you have a
better experience in using critical real time services like Internet phone, video conference …etc.
All the applications not specified by you are classified as rule name “Others”. The rule with a
smaller priority number has a higher priority; the rule with a larger priority number has a lower
priority. You can adjust the priority of the rules by moving them up or down.
Enable/Disable QoS: You can check “Enable QoS” to enable QoS functionality for the
WAN port.
Add a QoS rule into the table: Click “Add” then enter a form of the QoS rule. Click
“Apply” after filling out the form the rule will be added into the table.
Remove QoS rules from the table: If you want to remove QoS rules from the table, select
the QoS rules you want to remove in the table and then click "Delete Selected". If you
want remove all QoS rules from the table, just click the "Delete All" button. Clicking
"Reset" will clear your current selections.
Edit a QoS rule: Select the rule you want to edit and click “Edit”, then enter the detail
form of the QoS rule. Click “Apply” after editing the form and the rule will be saved.
Adjust QoS rule priority: You can select the rule and click “Move Up” to make its priority
higher. You also can select the rule and click “Move Down” to make its priority lower.
Click Apply at the bottom of the screen to save the above configuration.
USB port
You can use the USB port in Server mode as a Samba server for filesharing in your home
network or in NetUSB mode as a virtual USB port on your computer. Please note that for NetUSB
mode you need the USB Port Control Center software installed on your computer.
Server name: Enter a name for the network share.
Workgroup: If you wish to add the share to your workgroup enter the workgroup name
here.
Description: Enter a desired description for the share.
Administrator: Enter a desired username for access to the share.
New Password: Enter the password for access to the share and confirm this password by
re-entering it in the Confirm password field
For netUSB make sure the radio button next to netUSB is selected and press Apply. Please see
Addendum A: USB Port Control Center for more information about netUSB.
Toolbox Settings
Sitecom Cloud Security
Antivirus software alone is not safe enough. You can now benefit from additional built-in
security in your modem or router. Protect all devices in your home network against cybercrime
while browsing. Activate in just one click, your network and devices are better secured than
ever before.
Your Sitecom device comes with a 6 month free Sitecom cloud security subscription.
Activating Sitecom Cloud Security
After you have set up your Sitecom device for internet access, open the web browser and enter
http://www.sitecomcloudsecurity.com in the address bar.
If the device has been properly configured the following web page should be shown.
Here you can see which security features are activated.
The Sitecom Cloud Security service offers the following protection options:
Anti-Malware
Anti-Phishing
Protection against unsafe websites
Advertisement blocking
With the protection of unsafe websites activated the Sitecom Cloud Security will always check if
a website is safe. If it is not safe it will inform you that is not safe to enter.
If you still wish to visit this webpage click on „proceed anyway‟. Alternatively click „Back to
Safety‟ so that your security will not be breached.
Configuring Sitecom Cloud Security
If you wish to change your security options or to extend your subscription at any time, open
http://www.sitecomcloudsecurity.com from your web browser.
You will be asked for a username and password. These can be found on the backlabel on the
bottom of your Sitecom router or modem.
If the login succeeded you can click on „Settings‟ to change your security options.
Or click „License‟ to renew your subscription.
Disabling Sitecom Cloud Security
If you wish to disable to Sitecom cloud security at any time, open the webpage of your Sitecom
product and log in with the supplied credentials (these can be found on the back label on the
bottom of your Sitecom device).
Go to Toolbox and select “Sitecom Cloud Security”.
Click the “Disable” radio button and click „Apply‟ for the settings to take effect.
Password
You can change the password required to log into the router's system web-based management.
Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive.
Current Password: Fill in the current password to allow changing to a new password.
New Password: Enter your new password.
Confirmed Password: Enter your new password again for verification purposes.
Click Apply at the bottom of the screen to save the above configuration.
Time Zone
The Time Zone allows your router to base its time on the settings configured here, which will
affect functions such as Log entries and Firewall settings.
Set Time Zone: Select the time zone of the country you are currently in. The router will
set its time based on your selection.
Time Server Address: You can set an NTP server address.
Enable Daylight Savings: The router can also take Daylight savings into account. If you
wish to use this function, you must check/tick the enable boxto enable your daylight
saving configuration (below).
Start Daylight Savings Time: Select the period in which you wish to start daylight
Savings Time.
End Daylight Savings Time: Select the period in which you wish to end daylight Savings
Time.
Click Apply at the bottom of the screen to save the above configuration.
Remote Management
The remote management function allows you to designate a host in the Internet the ability to
configure the Broadband router from a remote site. Enter the designated host IP Address in the
Host IP Address field.
Host Address: This is the IP address of the host in the Internet that will have
management/configuration access to the Broadband router from a remote site. If the
Host Address is left 0.0.0.0 this means anyone can access the router‟s web-based
configuration from a remote location, providing they know the password.
Port: The port number of the remote management web interface.
Enabled: Select “Enabled” to enable the remote management function.
Click Apply at the bottom of the screen to save the above configuration.
Firmware Upgrade
Enable automatic firmware update: When enabled the router will periodically check if a new
firmware is available. If a new firmware is detected the router will give a notification.
Firmware Upgrade: This tool allows you to upgrade the Broadband router‟s system firmware. To
upgrade the firmware of your Broadband router, you need to download the firmware file to
your local hard disk, and enter that file name and path in the appropriate field on this page. You
can also use the Browse button to find the firmware file on your PC.
Once you‟ve selected the new firmware file, click Apply at the bottom of the screen to start the
upgrade process.
Backup Settings
The Backup screen allows you to save (Backup) the current configuration settings. When you
save the configuration setting (Backup) you can re-load the saved configuration into the router
through the Restore selection. If extreme problems occur you can use the Restore to Factory
Defaults selection, this will set all configurations to its original default settings (e.g. when you
first purchased the router).
Use the "Backup" tool to save the current configuration to a file named "config.bin" on your PC.
You can then use the "Restore" tool to restore the saved configuration to the router.
Alternatively, you can use the "Restore to Factory Defaults" tool to force the router to perform a
power reset and restore the original factory settings.
Reset
You can reset the router‟s system should any problem exist. The reset function essentially re-
boots your router‟s system.
DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You must get an
account, password and your static domain name from the DDNS service providers. This router
supports DynDNS, TZO and other common DDNS service providers.
Enable/Disable: Enable or disable the DDNS function of this router
Provider: Select a DDNS service provider
Domain name: Fill in your static domain name that uses DDNS
Account/E-mail: The account that your DDNS service provider assigned to you
Password/Key: The password you set for the DDNS service account above
Click Apply at the bottom of the screen to save the above configuration.
Addendum A: USB Port Control Center
The netUSB functionality of your router requires additional software to work with your
computer. The following section will describe how the software can be installed and used.
Windows
Insert the CD-ROM that was included with your router and select install utility from the cd-
menu.
The software will inform you about what will be installed.
Click Next to continue the installation.
Enter your username and organization if applicable and click Next to continue.
Choose a folder where the software should be installed or keep it to default and click Next to
continue.
The software is now ready to be installed, Click Install to continue.
Once the installation is finished the software will inform you. If Launch Sitecom USB Device
Serverchecked the software will automatically be launched after you clicked Finish.
MacOS
Insert the CD-ROM that was included with your router and select Install from the cd-menu.
Click Install to continue installation.
Enter your Mac username and password and click OK to continue.
Once the installation is finished the software will inform you and requires to restart the system.
Connect & Disconnect
“NetUSB” allows you to use USB printers when they‟re actually connected to the Sitecom USB
server.
The “connect” operation is a software operation that simulates an actual USB device plug-in.
Therefore, when you do a “connect” operation in the Control Center, the PC can detect a USB
device‟s plug-in, although actually you do not plug in any USB device to your PC. Similarly, the
“disconnect” operation is a software operation that simulates the disconnection of the USB
device.
Note: If a USB device is “connected” by a PC, we say that PC has the ownership of the USB
device. Only one PC can get the ownership of a USB device at the same time.
NetUSB installation
The steps to do installation for USB devices, like MFPs:
Make sure the router is turned on.
Connect the USB device to the USB port of the router.
Run the Control Center. In the “USB MFP Server List” window, you can see the host
names and IP addresses all of the Sitecom servers (in blue) on the network, as
shown below.
Click the server. Then all USB devices attached to the server will be shown.
Please follow the user manual of the USB device to install its driver. For example,
you may put the driver CD of the USB device in the CD-ROM player to install the
driver.
When you are asked to plug in the USB device into PC‟s USB port, click the desired
USB device in the Control Center and then click the “Auto-Connect Printer” button
to do the connect operation and get the ownership of the USB device. The
computer name of the device owner will be shown at the end of the device.
PC will automatically detect that the USB device is plugged-in. On the right side of
the Windows Task Bar, you can see the information of the new device. Continue to
follow the user manual of the USB device to do the rest jobs of installation, until the
driver installation has finished.
After the installation, you can see the newly created devices on the PC. If the USB device is a
MFP, you can see a new printer and a new scanner from the “Control Panel”.
NetUSB Printing using Auto-Connect Printer
After the driver is installed, you can see a newly created printer in the Control Panel. Follow the
steps below to perform NetUSB printing.
In the Control Center, click the MFP server that has the desired printer (or MFP)
attached.
Click the desired printer (or MFP).
Click the “Auto Connect Printer” button and choose “Set Auto-Connect Printer”.
The following figure will appear.
Choose the desired printer. The desired printer must be the Windows printer (this is
a logical printer) that matches the printer attached on the MFP server (this is a
physical printer). Then click the “Apply” button.
Then, the printer will be marked as an “Auto-Connected Printer” in red. If you choose
“Auto-Connected Printer List” in the “Tools” menu, you can see a newly created item
that describes the association between the Windows printer and the physical printer
on the server.
Then try to issue a print job to the desired printer. You will see the Control Center
will automatically do a connect operation and, once the print job finished, it will
hold the connection. However, the connection will be released immediately when
another user do the printing afterward. At the same time, the printer is
automatically disconnected with your PC.
When you do a print job again. The control center will automatically do a
connecting operation on printing again. This is so-called “Auto Connect /
Disconnect” operation.
Note: Under the “Auto-Connected Printer” setting, it is not necessary to manually press the
Connect” button when printing. If you press the “Connect” button for printing, please make
sure to click “Disconnect” button after you finish the printing. Otherwise, other users cannot
print properly. It is because you are the only ownership of the connected printer.
AutoRun
You can make the Control Center be run automatically after you login Windows. To do this, you
choose the “Configuration” item in the “Tools” menu. The following window will appear. Click
the check box and then on the “OK” button. This feature is enabled by default.
NetUSB Scanning using Network Scanning
In the Control Center, click the MFP server that has the desired MFP attached.
Click the desired MFP.
Click the “Network Scanner” button.
Then you can see that the Control Center will automatically do a “connect”
operation. The following window will appear.
Choose one of TWAIN or WIA item. Click “OK”. The following window will appear.
Follow the usual steps to do scanning.
Addendum B: GNU/GPL Leaflet
Licensing Information
Parts of the firmware of the WLR-8100 WiFi Router are subject to the GNU general public license.
This product includes third-party software licensed under the terms of the GNU General Public License..
You can modify or redistribute this free software under the terms of the GNU General Public License.
Please see Appendix B for the exact terms and conditions of this license.
Specifically, the following part of this product is subject to the GNU GPL:
#
Package name
Source
1
Linux v2.6.31
www.kernel.org
2
busybox v1.13
http://www.busybox.net/
3
uboot v1.1.4
http://www.denx.de/wiki/U-Boot
4
gcc v4.3.4
http://gcc.gnu.org/
5
iptables v1.4.4
http://www.netfilter.org/projects/iptables/index.html
6
iproute2-2.6.34
http://www.netfilter.org/projects/iptables/index.html
7
mtd-utils
http://processors.wiki.ti.com/index.php/MTD_Utilities
8
zlib v1.2.3
http://www.zlib.net/
9
termcap v1.3.1
ftp://ftp.gnu.org/gnu/termcap
10
pcre v6.x
http://www.pcre.org/
11
popt v1.7
http://freecode.com/projects/popt
12
libupnp v1.6.0
http://pupnp.sourceforge.net/
13
libreadline
http://cnswww.cns.cwru.edu/php/chet/readline/rltop.html#
CurrentStatus
14
libtirpc-0.2.x
http://downloads.sourceforge.net/project/libtirpc/libtirpc/0.
2.3/libtirpc-0.2.3.tar.bz2
15
libexif-0.6.x
http://sourceforge.net/projects/libexif
16
jpeg-6b
http://code.google.com/p/google-desktop-for-linux-
mirror/downloads/detail?name=jpeg-6b.tar.gz&can=2&q
17
ffmpeg-0.6.x
http://sourceforge.net/projects/ffmpeg
18
libid3tag-0.15.x
http://sourceforge.net/projects/mad/files/libid3tag/
19
flac-1.2.x
http://sourceforge.net/projects/flac
20
libogg-1.1.x
http://sourceforge.net/projects/libogg
21
libvorbis-1.2.x
http://downloads.xiph.org/releases/vorbis/
22
libiconv-1.13.x
http://sourceforge.net/projects/libiconv
23
uclibc v0.9.29
http://www.uclibc.org
24
sqlite-3.7.x
http://www.sqlite.org/
25
udhcp v0.9.9-pre
http://sources.busybox.net/index.py/trunk/udhcp-
web/index.html?revision=9967
26
igmpproxy v0.1-beta2
http://sourceforge.net/projects/igmpproxy
27
accel-pptp
http://sourceforge.net/projects/accel-pptp
28
minidlna-1.0.24
http://sourceforge.net/projects/minidlna
29
brctl2
http://www.busybox.net/
30
utelnetd-0.1.9
http://sourceforge.net/projects/utelnetd
31
dnsmasq-2.x
http://thekelleys.org.uk/dnsmasq/doc.html
32
ppp v2.4.3
http://ppp.samba.org
33
rp-pppoe-3.x
http://www.roaringpenguin.com/products/pppoe
34
pptp-client
http://pptpclient.sourceforge.net/
35
linuxigd-1.x
http://www.sourceforge.net/projects/upnp
36
uuidgen
http://www.ossp.org/pkg/lib/uuid/
37
ez-ipupdate
http://sourceforge.net/projects/ez-ipupdate
38
updatedd-2.6
http://sourceforge.net/projects/updatedd
39
ntpclient
http://doolittle.icarus.com/ntpclient/
40
hotplug2-1.x
http://code.google.com/p/hotplug2/
Availability of source code
Sitecom Europe BV has made available the full source code of the GPL licensed software, including any
scripts to control the compilation and installation of the object code on the CDROM that‟s included with
the product.
No Warranty
The free software included in this product is distributed in the hope that it will be useful, but WITHOUT
ANY LIABILITY OF OR ANY WARRANTY FROM THE LICENSOR.
Addendum C: GNU/GPL
Version 3, 29 June 2007 Copyright © 2007 Free Software Foundation, Inc. http://fsf.org/
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is
not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to
share and change the works. By contrast, the GNU General Public License is intended to guarantee your
freedom to share and change all versions of a program--to make sure it remains free software for all its
users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it
applies also to any other work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for
them if you wish), that you receive source code or can get it if you want it, that you can change the
software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to
surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software,
or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to
the recipients the same freedoms that you received. You must make sure that they, too, receive or can
get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software,
and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free
software. For both users' and authors' sake, the GPL requires that modified versions be marked as
changed, so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside
them, although the manufacturer can do so. This is fundamentally incompatible with the aim of
protecting users' freedom to change the software. The systematic pattern of such abuse occurs in the
area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we
have designed this version of the GPL to prohibit the practice for those products. If such problems arise
substantially in other domains, we stand ready to extend this provision to those domains in future
versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to
restrict development and use of software on general-purpose computers, but in those that do, we wish to
avoid the special danger that patents applied to a free program could make it effectively proprietary. To
prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor
masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as
“you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright
permission, other than the making of an exact copy. The resulting work is called a “modified version” of
the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or
secondarily liable for infringement under applicable copyright law, except executing it on a computer or
modifying a private copy. Propagation includes copying, distribution (with or without modification),
making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies.
Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a
convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells
the user that there is no warranty for the work (except to the extent that warranties are provided), that
licensees may convey the work under this License, and how to view a copy of this License. If the interface
presents a list of user commands or options, such as a menu, a prominent item in the list meets this
criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it.
“Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized
standards body, or, in the case of interfaces specified for a particular programming language, one that is
widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is
included in the normal form of packaging a Major Component, but which is not part of that Major
Component, and (b) serves only to enable use of the work with that Major Component, or to implement a
Standard Interface for which an implementation is available to the public in source code form. A “Major
Component”, in this context, means a major essential component (kernel, window system, and so on) of
the specific operating system (if any) on which the executable work runs, or a compiler used to produce
the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to
generate, install, and (for an executable work) run the object code and to modify the work, including
scripts to control those activities. However, it does not include the work's System Libraries, or general-
purpose tools or generally available free programs which are used unmodified in performing those
activities but which are not part of the work. For example, Corresponding Source includes interface
definition files associated with source files for the work, and the source code for shared libraries and
dynamically linked subprograms that the work is specifically designed to require, such as by intimate
data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other
parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are
irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited
permission to run the unmodified Program. The output from running a covered work is covered by this
License only if the output, given its content, constitutes a covered work. This License acknowledges your
rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as
your license otherwise remains in force. You may convey covered works to others for the sole purpose of
having them make modifications exclusively for you, or provide you with facilities for running those
works, provided that you comply with the terms of this License in conveying all material for which you do
not control copyright. Those thus making or running the covered works for you must do so exclusively on
your behalf, under your direction and control, on terms that prohibit them from making any copies of
your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below.
Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law
fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or
similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological
measures to the extent such circumvention is effected by exercising rights under this License with
respect to the covered work, and you disclaim any intention to limit operation or modification of the
work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid
circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program's source code as you receive it, in any medium, provided
that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep
intact all notices stating that this License and any non-permissive terms added in accord with section 7
apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of
this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or
warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in
the form of source code under the terms of section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any
conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact
all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into
possession of a copy. This License will therefore apply, along with any applicable section 7 additional
terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives
no permission to license the work in any other way, but it does not invalidate such permission if you have
separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if
the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not
make them do so.
A compilation of a covered work with other separate and independent works, which are not by their
nature extensions of the covered work, and which are not combined with it such as to form a larger
program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the
compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's
users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not
cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that
you also convey the machine-readable Corresponding Source under the terms of this License, in one of
these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution
medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily
used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution
medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer
spare parts or customer support for that product model, to give anyone who possesses the object code
either (1) a copy of the Corresponding Source for all the software in the product that is covered by this
License, on a durable physical medium customarily used for software interchange, for a price no more
than your reasonable cost of physically performing this conveying of source, or (2) access to copy the
Corresponding Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the
Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you
received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer
equivalent access to the Corresponding Source in the same way through the same place at no further
charge. You need not require recipients to copy the Corresponding Source along with the object code. If
the place to copy the object code is a network server, the Corresponding Source may be on a different
server (operated by you or a third party) that supports equivalent copying facilities, provided you
maintain clear directions next to the object code saying where to find the Corresponding Source.
Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is
available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the
object code and Corresponding Source of the work are being offered to the general public at no charge
under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as
a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is
normally used for personal, family, or household purposes, or (2) anything designed or sold for
incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases
shall be resolved in favor of coverage. For a particular product received by a particular user, “normally
used” refers to a typical or common use of that class of product, regardless of the status of the particular
user or of the way in which the particular user actually uses, or expects or is expected to use, the product.
A product is a consumer product regardless of whether the product has substantial commercial,
industrial or non-consumer uses, unless such uses represent the only significant mode of use of the
product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other
information required to install and execute modified versions of a covered work in that User Product from
a modified version of its Corresponding Source. The information must suffice to ensure that the
continued functioning of the modified object code is in no case prevented or interfered with solely
because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product,
and the conveying occurs as part of a transaction in which the right of possession and use of the User
Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction
is characterized), the Corresponding Source conveyed under this section must be accompanied by the
Installation Information. But this requirement does not apply if neither you nor any third party retains the
ability to install modified object code on the User Product (for example, the work has been installed in
ROM).
The requirement to provide Installation Information does not include a requirement to continue to
provide support service, warranty, or updates for a work that has been modified or installed by the
recipient, or for the User Product in which it has been modified or installed. Access to a network may be
denied when the modification itself materially and adversely affects the operation of the network or
violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must
be in a format that is publicly documented (and with an implementation available to the public in source
code form), and must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from
one or more of its conditions. Additional permissions that are applicable to the entire Program shall be
treated as though they were included in this License, to the extent that they are valid under applicable
law. If additional permissions apply only to part of the Program, that part may be used separately under
those permissions, but the entire Program remains governed by this License without regard to the
additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions
from that copy, or from any part of it. (Additional permissions may be written to require their own
removal in certain cases when you modify the work.) You may place additional permissions on material,
added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if
authorized by the copyright holders of that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this
License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that material or
in the Appropriate Legal Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of
such material be marked in reasonable ways as different from the original version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service
marks; or
f) Requiring indemnification of licensors and authors of that material by anyone who conveys the
material (or modified versions of it) with contractual assumptions of liability to the recipient, for any
liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of
section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed
by this License along with a term that is a further restriction, you may remove that term. If a license
document contains a further restriction but permits relicensing or conveying under this License, you may
add to a covered work material governed by the terms of that license document, provided that the
further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files,
a statement of the additional terms that apply to those files, or a notice indicating where to find the
applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license,
or stated as exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any
attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under
this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is
reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your
license, and (b) permanently, if the copyright holder fails to notify you of the violation by some
reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright
holder notifies you of the violation by some reasonable means, this is the first time you have received
notice of violation of this License (for any work) from that copyright holder, and you cure the violation
prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have
received copies or rights from you under this License. If your rights have been terminated and not
permanently reinstated, you do not qualify to receive new licenses for the same material under section
10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary
propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to
receive a copy likewise does not require acceptance. However, nothing other than this License grants you
permission to propagate or modify any covered work. These actions infringe copyright if you do not
accept this License. Therefore, by modifying or propagating a covered work, you indicate your
acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original
licensors, to run, modify and propagate that work, subject to this License. You are not responsible for
enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of
one, or subdividing an organization, or merging organizations. If propagation of a covered work results
from an entity transaction, each party to that transaction who receives a copy of the work also receives
whatever licenses to the work the party's predecessor in interest had or could give under the previous
paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in
interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this
License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in
a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or
importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on
which the Program is based. The work thus licensed is called the contributor's “contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the contributor,
whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by
this License, of making, using, or selling its contributor version, but do not include claims that would be
infringed only as a consequence of further modification of the contributor version. For purposes of this
definition, “control” includes the right to grant patent sublicenses in a manner consistent with the
requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the
contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify
and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however
denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not
to sue for patent infringement). To “grant” such a patent license to a party means to make such an
agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of
the work is not available for anyone to copy, free of charge and under the terms of this License, through a
publicly available network server or other readily accessible means, then you must either (1) cause the
Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent
license for this particular work, or (3) arrange, in a manner consistent with the requirements of this
License, to extend the patent license to downstream recipients. “Knowingly relying” means you have
actual knowledge that, but for the patent license, your conveying the covered work in a country, or your
recipient's use of the covered work in a country, would infringe one or more identifiable patents in that
country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by
procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the
covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work,
then the patent license you grant is automatically extended to all recipients of the covered work and
works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the
exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted
under this License. You may not convey a covered work if you are a party to an arrangement with a third
party that is in the business of distributing software, under which you make payment to the third party
based on the extent of your activity of conveying the work, and under which the third party grants, to any
of the parties who would receive the covered work from you, a discriminatory patent license (a) in
connection with copies of the covered work conveyed by you (or copies made from those copies), or (b)
primarily for and in connection with specific products or compilations that contain the covered work,
unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses
to infringement that may otherwise be available to you under applicable patent law.
12. No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the conditions of this License. If you cannot
convey a covered work so as to satisfy simultaneously your obligations under this License and any other
pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to
terms that obligate you to collect a royalty for further conveying from those to whom you convey the
Program, the only way you could satisfy both those terms and this License would be to refrain entirely
from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered
work with a work licensed under version 3 of the GNU Affero General Public License into a single
combined work, and to convey the resulting work. The terms of this License will continue to apply to the
part which is the covered work, but the special requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may differ
in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered
version of the GNU General Public License “or any later version” applies to it, you have the option of
following the terms and conditions either of that numbered version or of any later version published by
the Free Software Foundation. If the Program does not specify a version number of the GNU General
Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License
can be used, that proxy's public statement of acceptance of a version permanently authorizes you to
choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional
obligations are imposed on any author or copyright holder as a result of your choosing to follow a later
version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect
according to their terms, reviewing courts shall apply local law that most closely approximates an
absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of
liability accompanies a copy of the Program in return for a fee.
END OF TERMS AND CONDITIONS
Addendum D: Declaration of Conformity
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sitecom WLR-8100 - X8 AC1750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sitecom WLR-8100 - X8 AC1750 in the language / languages: English as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info