432355
29
Zoom out
Zoom in
Previous page
1/59
Next page
WL-614
300N Wireless Router
(802.11bgn draft 2.0)
User Manual
Revision:1.0
TABLE OF CONTENTS
1KEY FEATURES ................................................................................................................................... 4
2PACKAGE CONTENTS ...................................................................................................................... 5
3PRODUCT LAYOUT ............................................................................................................................ 6
4NETWORK + SYSTEM REQUIREMENTS ..................................................................................... 8
5WL-614 PLACEMENT ......................................................................................................................... 8
6SETUP LAN, WAN ................................................................................................................................ 9
7PC NETWORK ADAPTER SETUP (WINDOWS XP) ................................................................... 10
8BRING UP THE WL-614 .................................................................................................................... 12
9 INITIAL SETUP WL-614 .................................................................................................................. 12
10 CONFIGURATION WIZARD ........................................................................................................ 21
11 WIRELESS SETTINGS ................................................................................................................... 23
12 FIREWALL SETTINGS .................................................................................................................. 33
13 ADVANCED SETTINGS ................................................................................................................ 39
14 TOOLBOX SETTINGS .................................................................................................................. 49
2
Introduction
Congratulations on your purchase of the WL-614 Wireless Network Broadband
Router. The WL-614 is compliant with draft 802.11n v 2.0 up to 6 times faster
than standard 802.11g based routers while still being compatible with
802.11g & 802.11b gadgets. The WL-614 is not only a Wireless Access Point,
but also doubles as a 4-port full-duplex Switch that connects your wired-
Ethernet devices together at.
At 300 Mbps wireless transmission rate, the Access Point built into the Router
uses advanced MIMO (Multi-Input, Multi-Output) technology to transmit
multiple steams of data in a single wireless channel, giving you seamless
access to multimedia content. Robust RF signal travels farther, eliminates
dead spots and extends network range. For data protection and privacy, the
WL-614 encodes all wireless transmissions with WEP, WPA, and WPA2
encryption.
With the inbuilt DHCP Server & powerful SPI firewall, the WL-614 protects
your computers against intruders and most known Internet attacks but
provides safe VPN pass-through. With incredible speed and QoS function of
802.11n(draft2.0), the WL-614 is ideal for media-centric applications like
streaming video, gaming, and VoIP telephony to run multiple media-intense
data streams through the network at the same time, with no degradation in
performance.
1 Key Features
Features Advantages
Incredible Data Rate up to
300Mbps*
Heavy data payloads such as
MPEG video streaming
IEEE 802.11n draft 2.0 Compliant
and backward compatible with
802.11b/g
Fully Interoperable with IEEE
802.11b / IEEE802.11g
compliant devices with legacy
protection
Four 10/100 Mbps Fast Switch Ports
(Auto-Crossover)
Scalability, extend your network.
Firewall supports Virtual Server
Mapping, DMZ, IP Filter, ICMP
Blocking, SPI
Avoids the attacks of Hackers or
Viruses from Internet
Support 802.1x authenticator,
802.11i (WPA/WPA2, AES), VPN
pass-through
Provide mutual authentication
(Client and dynamic encryption
keys to enhance security
WDS (Wireless Distribution
System)
Make wireless AP and Bridge
mode simultaneously as a
wireless repeater
* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual
throughput may vary. Network conditions and environmental factors lower actual throughput rate.
All specifications are subject to change without notice.
2 Package Contents
Open the package carefully, and make sure that none of the items listed
below are missing. Do not discard the packing materials, in case of return;
the unit must be shipped back in its original package.
1. WL-614 Router
2. 220V~240V Power Adapter
3. Quick Install Guide
4. CD (User’s Manual)
5. Warranty card
6. UTP cable
3 Product Layout
Port Description
Power connector Connect the 12V DC adapter to this port
WAN (Blue) Connect your ADSL/Cable modem to this port
LAN (Yellow) Connect your PC’s or network devices to this port
Backlabel
The backlabel describes the IP address, login details, SSID, security code and
WPS button functionality.
Button Description
WPS BUTTON
Press 2 seconds for WPS mode
Press 10 seconds to reset the router
Press 15 Seconds to reset the router to factory defaults.
4 Network + System Requirements
To begin using the WL-614, make sure you meet the following as minimum
requirements:
PC/Notebook.
Operating System – Microsoft Windows XP/2000/VISTA
1 Free Ethernet port.
WiFi card/USB dongle (802.11 b/g/n) – optional.
External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera)
Ethernet compatible CAT5 cables.
5 WL-614 Placement
You can place the WL-614 on a desk or other flat surface, or you can mount it on
a wall. For optimal performance, place your Wireless Broadband Router in the
center of your office (or your home) in a location that is away from any potential
source of interference, such as a metal wall or microwave oven. This location
must be close to a power connection and your ADSL/Cable modem.
6 Setup LAN, WAN
WAN connection:
LAN connection:
7 PC Network Adapter setup (Windows XP)
Enter [Start Menu] select [Control panel] select [Network].
Select [Local Area Connection]) icon=>select [properties]
Select [Internet Protocol (TCP/IP)] =>Click [Properties].
Select the [General] tab.
a. The WL-614 supports [DHCP] function, please select both [Obtain an IP
address automatically] and [Obtain DNS server address automatically].
8 Bring up the WL-614
Connect the supplied power-adapter to the power inlet port and connect it to
a wall outlet. The WL-614 automatically enters the self-test phase. During
self-test phase, the Power LED will be lit continuously to indicate that this
product is in normal operation.
9 Initial Setup WL-614
LOGIN procedure
1. OPEN your browser (e.g. Internet Explorer).
2. Type http://192.168.0.1 in address bar and press [Enter]
3. Type user name and password (default is admin/admin).
4. Click OK.
5. You will see the home page of the WL-614.
The System status section allows you to monitor the current status of your router
the UP time, hardware information, serial number as well as firmware version
information is displayed here.
LAN settings
The LAN tab gives you the opportunity to change the IP settings of the WL-614.
Click <Apply> at the bottom of this screen to save any changes.
IP address 192.168.0.1. It is the router’s LAN IP address (Your LAN clients default
gateway IP address).
IP Subnet Mask 255.255.255.0 Specify a Subnet Mask for your LAN segment.
802.1d Spanning Tree is Disabled by default. If the 802.1d Spanning Tree function
is enabled, this router will use the spanning tree protocol to prevent network loops.
DHCP Server Enabled by default. You can enable or disable the DHCP server.
When DHCP is disabled no ip-addresses are assigned to clients and you have to
use static ip-addresses. When DHCP server is enabled your computers will be
assigned an ip-address automatically until the lease time expires.
Lease Time Forever. In the Lease Time setting you can specify the time period
that the DHCP lends an IP address to your LAN clients. The DHCP will change
your LAN client’s IP address when this time threshold period is reached.
IP Address Pool You can select a particular IP address range for your DHCP
server to issue IP addresses to your LAN Clients.
Note: default IP range 192.168.0.100

192.168.0.200. If you want your PC(s) to have a static/
fixed IP address, then you’ll have to choose an IP address outside this IP address Pool
Domain Name You can specify a Domain Name for your LAN. Or just keep the
default (sitecomwl34x).
Device Status
View the Broadband router’s current configuration settings. Device Status displays
the configuration settings you’ve configured in the Wizard / Basic Settings /
Wireless Settings section.
Internet Status
This page displays whether the WAN port is connected to a Cable/DSL connection.
It also displays the router’s WAN IP address, Subnet Mask, and ISP Gateway as
well as MAC address, the Primary DNS. Press Renew button to renew your WAN
IP address.
DHCP Client Status
DHCP This page shows all DHCP clients (LAN PCs) currently connected to your
network. The table shows the assigned IP address, MAC address and expiration
time for each DHCP leased client. Use the Refresh button to update the available
information.
You can check Enable Static DHCP IP. It is possible to add more static DHCP IPs.
They are listed in the table Current Static DHCP Table. IP can be deleted at will
from the table.
Click apply button to save the changed configuration.
WL-614 Log
View the operation log of the WL-614. This page shows the current system log of
the Broadband router. It displays any event occurred after system start up. At the
bottom of the page, the system log can be saved <Save> to a local file for further
processing or the system log can be cleared <Clear> or it can be refreshed
<Refresh> to get the most updated information. When the system is powered down,
the system log will disappear if not saved to a local file.
WL-614 Statistics
Shows the counters of packets sent and received on WAN, LAN & WLAN.
10 Configuration Wizard
Click Wizard to configure the router. The Setup wizard will now be displayed;
check that the modem is connected and click Next.
Select your country from the Country list. Select your internet provider. Click
Next.
Depending on the chosen provider, you may need to enter your user name
and password, MAC address or hostname in the following window. After you
have entered the correct information, click Next.
Click APPLY to complete the configuration.
11 Wireless Settings
You can set parameters that are used for the wireless stations to connect to this
router. The parameters include Mode, ESSID, Channel Number and Associated
Client.
Wireless Function
Enable or Disable Wireless function here. Click Apply and wait for module to
be ready & loaded.
Basic Settings
Mode Allows you to set the AP to AP, Station, Bridge or WDS mode.
Band Allows you to set the AP fixed at 802.11b or 802.11g mode. You can
also select B+G mode to allow 80211b and 802.11g clients at the same time.
Enable SSID # Allows you to enable up to four SSIDs for this router.
SSID This is the name of the wireless signal which is broadcasted. All the
devices in the same wireless LAN should have the same ESSID.
Channel The channel used by the wireless LAN. All devices in the same
wireless LAN should use the same channel.
Advanced Settings
This tab allows you to set the advanced wireless options. The options included
are Authentication Type, Fragment Threshold, RTS Threshold, Beacon
Interval, and Preamble Type. You should not change these parameters unless
you know what effect the changes will have on the router.
Authentication Type There are two authentication types: "Open System"
and "Shared Key". When you select "Open System", wireless stations can
associate with this wireless router without WEP encryption. When you select
"Shared Key", you should also setup a WEP key in the "Encryption" page.
After this has been done, make sure the wireless clients that you want to
connect to the device are also setup with the same encryption key.
Fragment Threshold "Fragment Threshold" specifies the maximum size of a
packet during the fragmentation of data to be transmitted. If you set this
value too low, it will result in bad performance.
RTS Threshold When the packet size is smaller then the RTS threshold, the
wireless router will not use the RTS/CTS mechanism to send this packet.
Beacon Interval is the interval of time that this wireless router broadcasts a
beacon. A Beacon is used to synchronize the wireless network.
Data Rate The “Data Rate” is the rate that this access point uses to transmit
data packets. The access point will use the highest possible selected
transmission rate to transmit the data packets.
N Data Rate The “Data Rate” is the rate that this access point uses to
transmit data packets for N compliant wireless nodes. Highest to lowest data
rate can be fixed.
Channel Bandwidth is the range of frequencies that will be used.
Preamble Type The Long Preamble” can provide better wireless LAN
compatibility while the “Short Preamble” can provide better wireless LAN
performance.
Broadcast ESSID If you enabled Broadcast ESSID”, every wireless station
located within the coverage of this access point can discover this access point
easily. If you are building a public wireless network, enabling this feature is
recommended. Disabling “Broadcast ESSID” can provide better security.
CTS Protection: It is recommended to enable the protection mechanism.
This mechanism can decrease the rate of data collision between 802.11b and
802.11g wireless stations. When the protection mode is enabled, the
throughput of the AP will be a little lower due to a lot of frame-network that is
transmitted.
TX Power can be set to a bare minimum or maximum power.
WMM WiFi Multi Media if enabled supports QoS for experiencing better audio,
video and voice in applications.
Security
This Access Point provides complete wireless LAN security functions, included
are WEP, IEEE 802.11x, IEEE 802.11x with WEP, WPA with pre-shared key
and WPA with RADIUS. With these security functions, you can prevent your
wireless LAN from illegal access. Please make sure your wireless stations use
the same security function, and are setup with the same security key.
Disable
When you choose to disable encryption, it is very insecure to operate the WL-
614.
Enable 802.1x Auth
IEEE 802.1x is an authentication protocol. Every user must use a valid
account to login to this Access Point before accessing the wireless LAN. The
authentication is processed by a RADIUS server. This mode only authenticates
users by IEEE 802.1x, but it does not encrypt the data during communication
WEP
When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to
encrypt data. You can generate the key by yourself and enter it. You can
enter four WEP keys and select one of them as a default key. Then the router
can receive any packets encrypted by one of the four keys.
Key Length You can select the WEP key length for encryption, 64-bit or 128-
bit. The larger the key will be the higher level of security is used, but the
throughput will be lower.
Key Format You may select ASCII Characters (alphanumeric format) or
Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.
Key1 - Key4 The WEP keys are used to encrypt data transmitted in the
wireless network. Use the following rules to setup a WEP key on the device.
64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or
5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit
Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters
as the encryption keys.
Click <Apply> at the bottom of the screen to save the above configurations.
You can now configure other sections by choosing Continue, or choose Apply
to apply the settings and reboot the device.
WPA Pre-shared Key
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a
pre-shared key to authenticate wireless stations and encrypt data during
communication. It uses TKIP or CCMP (AES) to change the encryption key
frequently. So the encryption key is not easy to be cracked by hackers. This is
the best security available.
WPA-Radius
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use
an external RADIUS server to authenticate wireless stations and provide the
session key to encrypt data during communication. It uses TKIP or CCMP
(AES) to change the encryption key frequently. Press Apply button when you
are done.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sitecom wireless router 300n limited edition wl 614 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sitecom wireless router 300n limited edition wl 614 in the language / languages: English as an attachment in your email.

The manual is 5,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info