616505
10
Zoom out
Zoom in
Previous page
1/12
Next page
10
Groove
(inside
holder)
6. When replacing the needle clamp, make
sure the needle bar is in its highest
position. Insert the needle clamp into
the needlebar, rotate and lightly push
upward till the pin seats into the needle
bar. Tighten the needle clamp screw
clockwise with 1.5mm Allen wrench.
Note: Replace the clear fabric cover with needle guard
and presser height adjusting screw before continuing
to use the machine.
Replacing the light bulb
For safety reasons, unplug main power
cord prior to replacing light bulb.
1. Make sure that the light bulb is
completely cool before removing it from
the machine.
2. Open lamp cover.
3. Remove the light bulb and replace new
one with the same type rated, MAX 15W.
Cleaning the lint box
Slide the atbed extension to the left to
remove it from the machine. Grasp the lint
box by the ridged nger grips in the front
and back and pull to the left to slide the lint
box off the machine.
Clean the lint out after each project.
An accumulation of lint in the box or under
the stitch plate may cause needle breakage.
Slide the lint box back into the machine.
11
We reserve the right to change the machine equipment and the ass ort ment of accessories
without prior notice, or make modi cations to the performance or design.
Such modi cations, however, will always be to the bene t of the user and the product.
Non-original Parts and Accessories
The warranty does not cover any defect or damage caused by use of non-original
accessories or parts.
English
Needle bent or Needle breakage
1. Are you moving the materials too quickly?
2. Are the needles touching the cloth presser or needle plate?
3. Is there dust or lint around the edge of the needles, cloth presser,or in the holes of the
needle plate?
4. Does the lint box area need to be cleaned?
For problems other than bent needles or needle breakage, please contact your retailer.
Speci cations
Needle: #S1037
Number of needles: 5
Needle Clamp: Round type
Feeding: Manual
Light bulb: MAX 15 W
Measurement: 435mm x 189mm x 292mm
Weight: 5.6 kg
Trouble Shooting
Please note that on disposal, this product must be safely recycled
in accordance with relevant National legislation relating to
electrical/electronic products. If in doubt please contact your
retailer for guidance.
34074 Singer ER10 Manual.indd 10 6/30/08 10:00:40 AM
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer ER-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer ER-10 in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info