617393

Singer 6680 Starlet Manual

26
Zoom out
Zoom in
Previous page
1/76
Next page
24
Lado plano
Lado plano hacia fuera de Vd.
Aguja
Pasador
CAMBIO DE LA AGUJA
1. Levantar la barra de la aguja a la posición
más alta girando el volante hacia Ud (en
sentido contrario a las manecillas del reloj).
2. Aflojar el tornillo que sujeta la aguja
girándolo hacia Ud (en sentido contrario a
las manecillas del reloj).
4XLWDUODDJXMDVDFiQGRODKDFLDDEDMR
4. Insertar la aguja nueva en la barra aguja con
el lado plano hacia la parte posterior.
5. Empujar la aguja lo más arriba posible.
6. Apriete el tornillo de sujeción de aguja con
el destornillador.
Consejo útil: Colocar un resto de
material debajo del prensatelas y bajar
el prensatelas facilita el cambio de aguja
y evita que la aguja baje en la ranura de
placa de aguja.
NOTA: Apriete firmemente, pero no
sobreapriete.
Siempre desconecte la máquina de la
fuente de alimentación retirando el
enchufe del tomacorriente de la pared.
Flat side
Côté plat
Flat side toward the back
Needle
Aiguille
Stop pin
Butée
1. Raise the needle bar to its highest
position by turning the hand wheel
toward you (counter-clockwise).
2. Loosen the needle clamp screw by
turning it toward you (counter-clockwise).
3. Remove the needle by pulling it
downward.
4. Insert the new needle into the needle
FODPSZLWKWKHÀDWVLGHWRZDUGWKHEDFN
5. Push the needle up as far as it can go.
6. Tighten the needle clamp screw with the
screw driver.
Helpful Hint: Placing a scrap of fabric
under the presser foot and lowering
the presser foot makes it easier to
change the needle and will preclude
dropping the needle into the needle
plate slot.
NOTE: Tighten snugly, but do not
over tighten.
CHANGING THE NEEDLE
Always disconnect the
machine from power supply
by removing the plug from the
wall-outlet.
Côté plat orienté vers l'arrière
CHANGEMENT D'AIGUILLE
1. Relevez la barre d'aiguille à sa position la plus
haute en tournant le volant vers vous (sens
antihoraire).
2. Desserrez la vis du serre-aiguille (sens
antihoraire).
3. Enlever l’aiguille en la tirant vers le bas.
4. Insérez la nouvelle aiguille dans le serre- aiguille,
le côté plat à l’arrière.
5. Poussez l’aiguille vers le haut, jusqu’à la butée.
6. Resserrez la vis de l’aiguille à l’aide du tournevis.
Conseil utile: en plaçant un morceau de
tissu sous le pied presseur et en abaissant le
pied presseur, vous faciliterez l’opération de
remplacement de l’aiguille, et ceci évitera
qu'une aiguille ne tombe dans la fente de la
plaque d'aiguille.
REMARQUE: resserrez-la correctement, mais pas
trop.
Débranchez toujours. La machine de
l’alimentation électrique en retirant la
che de la prise murale.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 6680 Starlet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 6680 Starlet in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info