459430
25
Zoom out
Zoom in
Previous page
1/64
Next page
23
Flat side
Côté plat
Lado plano
Flat side toward the back
Lado plano hacia fuera de Vd.
Côté plat orienté vers l’arrière
Needle
Aiguille
Aguja
Stop pin
Butée
Pasador
1. Raise the needle bar to its highest position by turning the
hand wheel toward you (counter-clockwise).
2. Loosen the needle clamp screw by turning it toward you
(counter-clockwise).
3. Remove the needle by pulling it downward.
4. Insert the new needle into the needle clamp with the flat
side toward the back.
5. Push the needle up as far as it can go.
6. Tighten the needle clamp screw with the screw driver.
Helpful Hint: Placing a scrap of fabric under the presser foot and lowering the
presser foot makes it easier to change the needle and will preclude dropping the
needle into the needle plate slot.
NOTE: Tighten snugly, but do not over tighten.
1. Relever la barre à aiguille à sa position la plus haute en tournant le volant vers vous
(sens antihoraire).
2. Desserrer la vis du serre-aiguille (sens antihoraire).
3. Enlever l’aiguille en la tirant vers le bas.
4. Insérer la nouvelle aiguille dans le serre- aiguille, avec le côté plat à l’arrière.
5. Pousser l’aiguille vers le haut, jusqu’ à la butée.
6. Resserrez la vis de l’aiguille à l’aide du tournevis.
Suggestion utile: En plaçant un morceau de tissu sous le pied presseur et en abaissant
le pied presseur, vous faciliterez l’opération de remplacement de l’aiguille, et ceci
évitera toute chute de l’aiguille dans la fente de la plaque-aiguille.
REMARQUE: Resserrez-la bien, mais pas trop.
CHANGING THE NEEDLE
CHANGEMENT D’AIGUILLE
CAMBIO DE LA AGUJA
Siempre desconecte la máquina de la
fuente de alimentación retirando el
enchufe del tomacorriente de la pared.
Débranchez toujours. La machine de
l’alimentation électrique en retirant
la che de la prise murale.
Always disconnect the machine
from power supply by removing the
plug from the wall-outlet.
1. Levantar la barra de la aguja a la posición más alta girando el volante hacia Ud (en sentido
contrario a las manecillas del reloj).
2. Aojar el tornillo que sujeta la aguja girándolo hacia Ud (en sentido contrario a las manecillas del reloj).
3. Quitar la aguja sacándola hacia abajo.
4. Insertar la aguja nueva en la barra aguja con el lado plano hacia la parte posterior.
5. Empujar la aguja lo más arriba posible.
6. Apriete el tornillo de sujeción de aguja con el destornillador.
Consejo útil: Colocar un resto de material debajo del prensatelas y bajar el prensatelas
facilita el cambio de aguja y evita que la aguja baje en la ranura de placa de aguja.
NOTA:Aprietermemente,peronosobreapriete.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 6199 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 6199 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 6,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Singer 6199

Singer 6199 User Manual - German, Italian - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info