459426
17
Zoom out
Zoom in
Previous page
1/40
Next page
30
7
Tirez le fil de la bobine. Maintenez-le fermement au-dessus du
premier guide-fil. Ensuite, tirez le fil vers le bas pour l'introduire
dans le guide-fil.
Enfilage de la machine
Winding the bobbin
Remplissage de la canette
Tournez le volant vers vous jusqu'à ce que l'aiguille soit
dans la position la plus haute.
Relevez le pied presseur.
Placez la bobine de fil sur le porte-bobine horizontal. Fixez
le fil dans la bonne position avec le grand ou le petit
capuchon de bobine, suivant la taille de votre bobine de fil.
Devanando la bobina
Gire el volante hacia usted hasta que la aguja esté en la
posición más alta.
Levante la palanca del prensatelas.
Deslice el hilo en el portacarrete horizontal. Asegure la hebra
en su sitio con el sujetador grande o pequeño, dependiendo
del tamaño del carrete de hilo.
Jale el hilo del carrete, sostengalo con firmeza sobre el primer guía hilos.
Posteriormente, jale el hilo hacia adentro del guía hilos.
Ensartando la Máquina
Turn handwheel counter clockwise until the needle is in the
highest position.
Raise presser foot lifter.
Slide thread onto horizontal spool pin. Secure thread in place
with either the large or small spool pin holder, depending on
the size of your thread spool.
Pull the thread from the spool, hold firmly over the first thread
guide. Then push the thread down, snapping it into the thread guide.
Threading the machine
3131
7
Faites passer le fil par un des trous de
la canette conformément à
l'illustration en laissant dépasser un
bout de fil de 10 cm.
Tirez le fil de la bobine et faites-le passer par le deuxième guide-fil.
Placez le fil à droite du disque de tension du dévidoir, puis faites-le passer à
gauche sous le disque et autour du disque, en tirant le fil vers le dévidoir de
canette.
Enfilage de la machine
Jale la hebra del carrete hacia el segundo guia hilos.
Coloque el hilo a la derecha del tensor, dé vuelta a la izquierda como se muestra en
la imagen, jale el hilo hacia el devanador de bobina.
Pase el hilo por uno de los orificios de
adentro hacia afuera de la bobina
como se muestra, dejando una hebra de
4 centimetros aproximadamente.
Ensartando la Máquina
Pull thread out from the spool through the second thread guide.
Place the thread to the right of the Bobbin winder disc, then swing the bobbin thread
to the left going under and around the disc, pulling the thread toward the Bobbin
winder.
Pull the thread through the hole in the
bobbin as shown, leaving a 4” tail.
Threading the machine
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 4228 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 4228 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info