570582

Singer 29K73 Manual

8
Zoom out
Zoom in
Previous page
1/13
Next page
TO THREAD NEEDLE FOR DARNING
1. Place the spool of thread on the spool pin so that thread
will draw from rear side of spool.
2. Raise the wire guide in the oil cup on top of the arm and
pass thread under guide then press guide back into
position. See fig. 19.
3. Pass thread over the pin 2 near the tension discs in front
of the arm and from right to left under and between the
tension discs 3, Fig. 21.
4. Pass thread through wire eyelet 4.
5. Pass thread up and from front to back through the hole
5 in the take-up lever.
6. Draw about 10 inches of thread through the hole in
take-up lever and insert the end into the slit in the end of
the threading wire supplied with the machine. Then pass
end of threading wire down through hole 6 which runs
through the centre of the needle bar.
7. Remove thread from threading wire then withdraw
threading wire. Pass the thread from left to right through
the eye of the needle 7. Draw about three inches of thread
through the eye of the needle with which to start darning.
Fig. 21. Upper thread for Darning
TO PREPARE FOR SEWING
With the left hand hold the end of the needle thread,
leaving it slack from the hand to the needle. Turn top of
hand wheel over toward you until the needle moves down
and up again to its highest point, thus catching
Fig. 22. Drawing up Bobbin Thread
the bobbin thread; draw up the needle thread and the
bobbin thread will come up with it through the hole in the
needle plate. See Fig. 22. Lay both threads back under the
feeding foot.
NOTE: Turn top of hand wheel over toward the right
(clockwise) if the hand wheel is fitted to the front of
machine.
TO START SEWING
Place the material under the feeding foot, lower the foot
and start to sew, turning the hand wheel over toward you.
(Turn hand wheel to the right if located on front of
machine.)
CAUTION: Do not try to help feeding of the work by
pulling the material as this may deflect the needle and
cause it to break. The machine feeds the work easily
without any assistance.
TO REMOVE THE WORK
Let the needle bar rest at its highest point, raise the
feeding foot, then draw the material backward about 3
inches and cut the threads close to the work. Leave the
ends of the threads under the feeding foot.
8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 29K73 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 29K73 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info