570580

Singer 29K71 Manual

7
Zoom out
Zoom in
Previous page
1/13
Next page
TO REPLACE THE SHUTTLE
After threading the shuttle, turn hand wheel until the upright
part of the shuttle carrier is to the right. Then with the point
of the shuttle nearest you, and pointing towards the right,
place it into the recess as shown in Fig. 17. With needle bar
at its highest point, press down lever C, Fig 17 and swing
back needle plate to its sewing position.
Fig. 17. Replacing Shuttle
TO SET THE NEEDLE
Raise needle bar to its highest point and loosen screw H,
Fig. 18. Then Insert shank of the needle up into the needle
clamp as far as it will go with long groove of the needle to
the left and its eye directly in line with the arm of the
machine. Tighten screw H, Fig. 18. Loosen screw G, Fig 18
and move the clamp to right or left, until the needle passes
through the centre hole in the needle plate, then tighten
screw G.
CAUTION: There are two double end needle plates
furnished with each machine. Be certain needle is straight
and corresponds to the correct needle hole size indicated on
end of needle plate.
Fig. 18. Setting the Needle
TO THREAD NEEDLE
Fig. 19. Threading Needle
1. Place the spool of thread on the spool pin so that
thread will draw from the rear side of spool. See Fig.
19.
2. Raise the wire guide in the oil cup on top of the arm
and pass thread under guide 1, then press guide back
into position.
3. Draw the thread around back of pin 2 which is near
the tension discs on top of the arm and from back to
front and right to left between the tension discs 3. See
Fig. 20.
4. Pass thread through wire eyelet 4.
5. Lead thread up and from front to back through the
hole 5 in the take up lever.
6. Draw about 10 inches of thread through the in the
take-up lever and insert the end into the slit in the end
of the threading wire supplied with the machine. The
pass end of the threading wire down through hole 6
which runs through the centre of the needle bar.
7. Remove thread from threading wire then withdraw
threading wire. Pass the thread from left to right
through the eye of the needle 7. Draw about three
inches of thread through the eye of the needle with
which to start sewing.
Fig. 20. Upper Threading
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 29K71 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 29K71 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info