616706
58
Zoom out
Zoom in
Previous page
1/60
Next page
56
HELPFUL MESSAGES
Messages are displayed with LED lamps above the stitch selection panel on the machine.
When a message is displayed, you may x the problem by following the correction suggestion most suited to your issue.
The corrections are preceded by an arrow.
SYSTEM ERROR
All system error corrections are as follows.

Turn off and on the power switch to eliminate the problem that caused the system error to occur.
If the error number should not disappear, consult an authorized technician.
Helpful message
on control panel
Problem
Correction
1. The bobbin winder shaft is in the incorrect position for the function you have selected.
Position the bobbin winder shaft to the left position for sewing and to the right position for
bobbin winding.
2. The reverse button is pressed during bobbin winding.
Do not press reverse button during bobbin winding.
1. Buttonhole stitch is selected on the stich control panel; however the buttonhole lever is not
in the correct position.
Lower buttonhole lever and begin sewing the buttonhole.
2. A stitch pattern is selected; however the buttonhole lever is engaged (lower position).
Raise buttonhole lever and begin sewing.
3. The buttonhole lever is in an incorrect starting position.
Lower the buttonhole lever so that it drops down vertically between the stoppers. See page
46 for details.
1. Something other than foot control is detected in the machine socket for the foot control.
Remove foreign particle from socket.
2. Foot control is connected or disconnected.
This is not an error message. It only indicates the connection or disconnection of the foot
control and the C3 message will disappear in a few seconds. No correction is needed.
1. Machine does not operate due to thread tangles in bobbin case or jamed fabric.
Turn off power switch and eliminate the problem that caused the machine to stop.
1. The stitch pattern selected, does not operate when the reverse/tacking stitch is pushed.
Select a stitch pattern that can be operated in the reverse/tacking stitch mode.
1. The top thread has broken.
Lift presser foot lifter. Pull to remove top thread from machine and rethread.
1. The foot controller was pushed down to start sewing before the presser foot was lowered.
Lower presser foot and begin sewing.
Misfunction of main shaft motor.
Abnormal signal from bobbin winder shaft.
Abnormal signal from cam sensors.
Reverse stitch button is engaged, when the power is tuned on.
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 160 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 10,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info