28558
22
Zoom out
Zoom in
Previous page
1/224
Next page
974-25007001/2.0 SL 30/35 Hull Sonar Operators Manual
Page 2.6 System Description
Kongsberg Simrad Mesotech Ltd.
Port Coquitlam, BC - Canada
2.1.5.1 Transceiver Unit
The Transceiver Unit is mounted on the tank flange in a standard installation, but
can also be bulkhead mounted if required. The maximum Sonar Dome cable length
permissible is 5.1 meters depending on the shaft length used during the installation.
The Transceiver Unit contains the receiver and transmitter PCB assembly and the
lower and raise PCB assembly. A safety power ON/OFF switch is also provided so
power can be shut off when working on the lower and raise assembly. The
transceiver assembly is splash proof to protect the electronics circuits from water.
Note: The safety power ON/OFF switch is not required for the SL 30 Sonar.
2.1.5.2 Lower and Raise Unit
The SL 35 Lower and Raise Unit is a self-contained hydraulic assembly. Installation
is simple and only requires the fitting of 2 clevis pins and connection of the power
cable from the Transceiver Unit.
.
The travel length is available in two sizes, 250 millimeters and 400 millimeters
depending on the installation requirement.
2.1.5.3 Hull Sonar Dome Unit
The Hull Sonar Dome unit is available in two frequencies, 90kHz and 160 kHz. The
cable length is available in 4.5 meters for a 2.4 or 3 meter shaft and 5.1 meters with
a 3.6 meters optional shaft. Special attention must be paid to matching cable and
shaft lengths when ordering the system.
Note: The SL 30 Catch Sonar Dome comes with a standard 5 meter cable length.
2.1.5.4 Tank Flange Assembly
The SL 35 Tank Flange Assembly main body is cast in ASTM A536, 60-40-18
Ductile Iron. Special mounting pads and a guide are incorporated into the flange.
The shaft bearing is made of SEA 660 Bearing Bronze. Special attention was given
during the design to the seal and shaft packing in order to prevent water leakage
into the sonar room. A zinc anode is also installed on the tank flange, to reduce
electrolysis.
Note: The Tank Flange Assembly is not required for the SL 30 Dome; all flanges are
serial-numbered.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad SL30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad SL30 in the language / languages: English as an attachment in your email.

The manual is 5,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info