572713
49
Zoom out
Zoom in
Previous page
1/66
Next page
|
49
Autopilot | NSS Installation Manual
If the value is set too high the overshoot will increase and the steering will be
unstable.
Counter rudder
Counter rudder is the amount of rudder used to try to prevent the boat from yawing
around the set course. Higher counter rudder settings result in more rudder being
applied.
The best way of checking the value of the Counter rudder setting is when making
turns.
The  gures illustrate the e ects of various Counter Rudder settings;
A: Counter rudder too low; overshoot response
B: Counter rudder too high; sluggish and creeping response
C: Correct setting or counter rudder; ideal response
ABC
Auto trim
This parameter de nes how fast the autopilot shall correspond after having registered
a heading error.
The standard value is 40 seconds which should work well on most boats. Rule of
thumb: Set to same value (seconds) as the boat’s length in feet. On boats operating
on VRF the value should be set to 20 seconds.
Rate limit
Sets the maximum allowed rate of turn.
The value should be kept at 6.0°/second unless there is a need for more rapid
response in turns.
Minimum rudder
This parameter  lters small rudder commands to prevent high rudder activity.
Some boats may have a tendency to not respond to small rudder commands around
the course keeping position because of a small rudder, a rudder deadband, whirls/
disturbance of the water-stream passing the rudder or it is a single nozzle water jet
boat.
By increasing the Minimum rudder parameter you may improve the course keeping
performance on some boats. This will however increase the rudder activity.
Minimum wind angle to port and starboard
These parameters should be set identical to the minimum apparent wind angle that
will keep the sails well shaped and give an acceptable thrust. The parameters will vary
from boat to boat.
The settings are used for the tack-prevent function. They also applies when the autopi-
lot is operating in WindNAV mode. Refer to the
Operating the autopilot section.
You can select di erent minimum wind angles for port and starboard. The di erence
between port and starboard will be taken into account when calculating the Distance
To Turn (DTT).
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad NSS Chartplotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad NSS Chartplotter in the language / languages: English as an attachment in your email.

The manual is 18,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Simrad NSS Chartplotter

Simrad NSS Chartplotter User Manual - English - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info