23322
41
Zoom out
Zoom in
Previous page
1/108
Next page
901-10037001/1.1 FS 20/25 Operators Manual
Page 4.4 FS 20/25 Installation, System Set-Up and Test
Kongsberg Simrad Mesotech Ltd.
Port Coquitlam, BC - Canada
Optional equipment for interface to the control unit may be mounted in any convenient
location provided the user supplied interconnect cables are of sufficient length and the
required power is available.
4.2.2 Power Considerations
The display unit, generally, will require 110 VAC or 220 VAC. Depending on the
capabilities of the unit chosen, it may automatically detect the supply voltage or the
unit may have to be ordered for the correct voltage.
The FS 20/25 HP PC processor will operate from either 110 VAC or 220 VAC. Voltage
selection must be selected, a voltage input selector switch is located at the rear of the
unit. Failure to select the proper Input voltage will damage the internal power supply
The FS 20/25 Power Supply/TTM module can be operated with either 110 VAC or 220
VAC. Selection of the supply voltage is done by moving the voltage selector card
located in the power entry module at the rear panel. Details on selecting the proper
voltage are indicated on the voltage card. You must position the “indicator pin” location
to the desired voltage. The safety fuses must also be changed to the proper rating.
Refer to Paragraph 4.2.7 for more detail.
4.2.3 Connecting a Display Unit
Either a VGA monitor CRT type or a Simrad LCD monitor may be connected to the
FS 20/25 HP PC processor. Depending on which type of monitor is used, the video
output type must be set accordingly.
An industry standard VGA monitor will connect directly to the miniature DB-15
connector located on the rear panel of the control unit.
The FS20/25 HP PC has a DualHead video interface card installed as standard
equipment. You must set up your display software as per your requirement. If you
have only one monitor, simply plug your monitor cable into the monitor connector
marked “Connector 1” on the adapter card, or Video “A” port. If you are using two
monitors, you must connect the 2
nd
monitor in the “Connector 2” on the adapter card,
or Video “B” port.
Note: The FS20/25 HP PC must be is turned “OFF” prior connecting the video
monitors
An HP User Guide manual is provided with the system, including a Recovery CD-
ROM. With this CD you can recover your system as delivered, run HP diagnostics.
Note: The DualHead software is installed at the factory, you only have to set up your
monitor configuration as per Window’s 2000. See Part 7 “Attachment” for set-up
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad FS25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad FS25 in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info