738922
7
Zoom out
Zoom in
Previous page
1/42
Next page
- 5 -
Mantener el agua caliente
Con este hervidor de agua puede mantener el
agua caliente a una temperatura de (aprox.) 40°C,
60°C, 80°C o 100°C durante 30 minutos. Si ha
puesta la temperatura de mantenimiento de calor
elegida a 100°C, el hervidor de agua mantendrá
el agua a una temperatura comprendida de aprox.
90°C y aprox. 100°C, con el fin de evitar una
formación de vapor excesiva. Si la temperatura
de mantenimiento de calor elegida es de 80°C,
60°C o 40°C, el hervidor de agua mantendrá
el agua a una temperatura entre aprox. 8°C por
debajo o bien por encima de la temperatura
seleccionada.
Atención
Utilice la función de mantenimiento de calor sólo
con mínimo 0,5 litros de agua en el hervidor de
agua. Si hay menos agua, se desconectará posible-
mente el hervidor de agua dentro de 30 minutos,
con el fin de proteger el elemento calefactor.
Advertencia
Extraiga la clavija de red de la base de enchufe
antes de levantar la jarra de la base
y
. De ese
modo evita que el agua que salpica fuera caiga
sobre las conexiones eléctricas de la base
y
y que
de este modo pueda provocarse un cortocircuito.
Peligro de lesiones
Por motivos de seguridad no debe abrir la tapa
si el agua está hirviendo o muy caliente. Existe
peligro de sufrir quemaduras.
El ajuste para el mantenimiento de calor deberá
realizarlo durante o justo después de finalizar el
proceso de hervir:
Indicaciones
Si no puede ajustar la temperatura deseada puede
ser debido a que la temperatura del agua en el
hervidor de agua aún es demasiado alta.
AAnntteess ddeell pprroocceessoo ddee hheerrvviirr
Pulse antes del proceso de hervir la tecla
KEEP WARM
w
.
Pulse la tecla SET TEMP
r
las veces necesarias
hasta que se ilumine el LED
q
a la temperatura
elegida.
Pulse la tecla Inicio para iniciar primero el pro-
ceso de cocción y a continuación el de manteni-
miento de calor.
El LED
q
de la temperatura ajustada actual brilla,
también el LED integrado en la tecla KEEP WARM
w
así como el LED de la tecla On/Off
e
.
Ahora el agua se mantendrá caliente después de
calentarla.
DDuurraannttee eell pprroocceessoo ddee hheerrvviirr
Inicie el proceso de hervir tal como se describe
en el capítulo "Calentar agua".
Pulse durante el proceso de hervir la tecla
KEEP WARM
w
.
Finalizado el proceso de hervir continua iluminándose
el LED
q
de la temperatura actual ajustada, el LED
integrado en la tecla KEEP WARM
w
, así como
el LED de la tecla On/Off
e
. Ahora el agua se
mantendrá caliente después de calentarla.
DDeessppuuééss ddeell pprroocceessoo ddee hheerrvviirr
Pulse después de la señal acústica que indica el
fin del proceso de hervir, la tecla KEEP WARM
w
.
El aparato ajusta automáticamente la temperatura
de mantenimiento de calor a la temperatura a la que
ha calentado el agua. El LED
q
de la temperatura
ajustada actual brilla, también el LED integrado en
la tecla KEEP WARM
w
así como el LED de la tecla
On/Off
e
. Ahora se mantiene el agua caliente.
IB_67146_SWKD3000A1_LB5 29.06.2011 9:52 Uhr Seite 5
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SWKD 3000 A1 IAN 67146 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SWKD 3000 A1 IAN 67146 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SWKD 3000 A1 IAN 67146

Silvercrest SWKD 3000 A1 IAN 67146 User Manual - German, Dutch, French, Italian - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info